轴向的

A high-strength steel pipe rockbolt has an expansive rockbolt main body prepared by processing a high-strength steel sheet of 1.8-2.3 mm in thickness with tensile strength of 490-640 N/mm 2 and elongation of 20% or more to a welded pipe and roll-forming the welded pipe to a shaped pipe having one or more concavities extending along an axial direction.

高强度钢管锚杆具有可膨胀锚杆主体，该主体通过下列步骤制成：将抗拉强度为490～640N/mm 2 ，伸长率为20％或更大，厚1.8～2.3mm的高强度钢板加工成焊接管，再将该焊接管滚轧成型成具有一个或多个沿轴向延伸的凹部的异形管。

The conclusions obtained are applicable for active accelerating and passive decelerating parts of trajectory as we...

在小推力和小轴向过载的情况下，各种不同的计算方法所得的结果相差不大。

A study in form and geometry, the plaza continues the form language of the axial connection and extrudes it into the third dimension through the addition of precast concrete seat walls set in plinths of decomposed granite and surrounded by mixed understory plantings.

研究的形式和几何，继续在广场的形式语言和挤出轴向连接到第三个层面通过增加预制混凝土墙壁座位设置在plinths的风化花岗岩，四周是混合林下种植。

The distribution and variation of plastic zone in the joint were calculated and analyzed during inertia friction welding process. And the variation of deformation rate of plasticized material was also simulated.

计算并分析了惯性摩擦焊接过程中接头塑性区的分布、扩展规律及其与工件轴向缩短的关系，并计算了塑性区金属塑性变形速率的分布和变化情况。

The corres- ponding computer program is also developed and has been used to work out a series of problems with satisfactory results.

文(8)建议最小二乘意义下的近似方法，目的是使连接点处两单元轴向位移差的平方泛函取极小，但是对二维及三维的薄壁杆件体系

Numerical simulations showed the axial velocity in the precessing flow were decreased significantly because of the entrainment of ambient air. The swirling motion, the wall attachment effect and the reverse flow were also found in the numerical flow field. It is shown that the simulation results of the precessing jet flow accord well with the analysis and the previous work.

数值模拟表明旋进射流的轴向流动速度衰减得很快，流场中存在明显的旋流、附壁效应和反向回流现象，所得到的结果与已有的分析结论基本吻合。

For internal high pressure forming of a hollow part with big difference on section perimeter, the problems of axial feeding and preforming are necessary to be solved to produce qualified parts with more uniform thickness distribution.

截面周长差较大的空心零件的内高压成形需要解决膨胀区的轴向补料问题和预成形问题，才能获得壁厚分布较为均匀的合格零件。

The conducting wall in micro-tube preheats the inlet mixture by axial heat transfer. The existence of conducting wall will help to reach full reaction in the micro-tube. As the inlet velocity increases, both the existence of the surface catalytic combustion and the gas phase combustion become the limiting factors on combustion. Wall material and equivalence ratio of hydrogen/air mixture have important influence on catalytic combustion of hydrogen.

计算结果表明：表面催化反应对空间气相反应有抑制作用；在微型管道内，通过导热壁轴向间的传热，预热入口混合气体，使氢气燃烧更加充分；随着入口速度的增大，燃烧过程同时存在着表面催化反应和空间气相反应两种控制因素；管壁材料和当量比对氢气的催化燃烧过程有重要的影响。

The sclera samples obtained after one month, two months, three months and six months were axial tensed in pretesting, relaxing, creeping and deforming. A series of dates and curves that represent conventional mechanical properties and viscoelastical properties were obtained.

选择简单可行的轴向拉伸的实验方法，分别对术后1月、2月、3月、6月加固条带区及对照眼相应区等5种兔眼巩膜试件进行预拉伸、应力松弛、蠕变及破坏的生物力学实验研究，得到一系列表示常规力学性质的数据和曲线，并进行统计、比较。

Both monotonic axial compressive and axially loaded cyclic tests have been carried out on the steel box brace used in New CCTV Building to investigate the effect of assembling welds including full penetration and partial penetration on the structural behavior of the brace.

为考察全熔透和部分熔透两种组装焊缝形式对箱形截面钢支撑受力性能的影响，本文对中央电视台新台址建设工程中的箱形截面支撑进行了单调受压、轴向反复拉压试验；同时，采用ABAQUS有限元软件实现了对部分熔透试件未熔透处的接触模拟和滞回性能模拟。

This one mode pays close attention to network credence foundation of the businessman very much.

这一模式非常关注商人的网络信用基础。

Cell morphology of bacterial ghost of Pasteurella multocida was observed by scanning electron microscopy and inactivation ratio was estimated by CFU analysi.

扫描电镜观察多杀性巴氏杆菌细菌幽灵和菌落形成单位评价遗传灭活率。