轴向的

The coefficients of load distribution along the contact line of pitch position in axial middle section are obtained.

应用它计算了六对齿轮在不同接触线上的载荷分布，得出齿轮在轴向中间截面节点位置啮合时接触线上的载荷分布系数，分析了轮齿刚度的变化规律，给出轮齿刚度的简化计算公式。

For the analysis of both static and dynamic characteristics, the additional moments, axial/radial coupled stiffness coefficients and the radial/radial coupled stiffness coefficients are taken into account Based on it, the influences of the bearing angle, the ratio of width to diameter, and the ration of magnetic polar angle on the static and dynamic characteristics conical magnetic bearing are analyzed, and the corresponding numerical results are presented.

在圆锥电磁轴承基础解的计算模型中，增加了轴承附加力矩、力矩刚度系数以及轴向/径向、径向/径向耦合刚度系数的计算。在此基础上，本文详细讨论了圆锥电磁轴承锥角、宽径比以及磁极角比对轴承静、动特性的影响，并给出了数值结果。

The temperature distribution was mainly influenced by the initial pressure of pressurizer under the condition of CMT drainage with sparger, the higher the pressure is, the thicker the hot water layer.

通过对CMT内水的轴向温度分析，发现CMT内的流体具有热分层特性，即上部为热水层，下部为冷水层，热水层内温度变化剧烈，吸收了蒸汽在液面凝结放出的大部分热量。

In Laplace space, the exact element stiffness matrix of the axial, torsional and bending vibrations of cone-shaped and symmetrical closed thin-walled bars are derived. By use of variation principle, the element stiffness matrix of the coupling vibrations of an asymmetrical closed thin-walled bar is also given.

在拉氏空间中导出了锥形杆件和对称闭口薄壁杆件的轴向、扭转和弯曲振动的精确单元刚度矩阵，应用变分原理也给出了非对称闭口薄壁杆件耦联振动的单元刚度矩阵。

Finish to design the micro CNC, I have to investigate the adaptable parameters for cutting. This paper had calculated tool's radius, spindle's rotational speed, radial depth, and feed speed by the instantaneous cutting areas of the cutting forces model. To find out the instantaneous cutting areas by mathematica which can calculate the tangential, radial and axial component of cutting forces during cutting.

设计完微型工具机后，接著探讨最佳的切削参数，本论文采用瞬时投影面积的数学模型，且推导出利用刀具半径、主轴转速、径向切深、进给速度等参数来做为瞬时切削投影面积的函数，并使用软体mathematica算出瞬间面积大小，预测出切削过程里所产生的切线切削力、径向切削力和轴向切削力。

Its surface speed must be and the speed of printing plate surface are equal, are not allowed in axial and radial runout, otherwise cause damage to the printing plate.

它的表面速度必须和印版表面的速度相等，不允许有轴向窜动和径向跳动，否则易引起印版的损坏。

In the present paper,the nonlinear behaviors of the chaotic bubbling from a 4-pipr gas sparger in a shallow bubble column s with three different high diameter ratios of one to three was studied.

鼓泡塔不同区域的奇怪吸引子结果表明：对于H/D≤3的气相多管分布的浅层鼓泡塔，沿轴向可区分为下部气泡分裂区、中部分裂与凝并过渡区和上部分裂凝并平衡区。

Experimental study was conducted on flow characteristics of catalyst in a standpipe with f108 mm4 mm and height of 10 m.

对垂直立管中催化剂的流动性能进行了实验研究，测定了各种操作条件下立管中的轴向压力分布、催化剂循环速率以及附加吹气的影响。

The swing car bridge with hydraulic pressure pendant is conected with hydraulic pressure assistant loop.,among which can get equal load.The heavy module use hydraulic pressure turning with two cycle loop.

带液压轴悬架的摆动车桥是与液压辅助回路（3点或4点支承）互联的，在这些辅助回路中可得到相等的轴向载荷。

Appropriate removal of the cervical central endplate will not undermine the axial stress of the cages or bone graft but could facilitate the synostosis.

适当地去除部分中央终板对内植物或植骨块的承受轴向应力的影响不大，同时能促进植骨块的融合，有着一定的临床价值。

This one mode pays close attention to network credence foundation of the businessman very much.

这一模式非常关注商人的网络信用基础。

Cell morphology of bacterial ghost of Pasteurella multocida was observed by scanning electron microscopy and inactivation ratio was estimated by CFU analysi.

扫描电镜观察多杀性巴氏杆菌细菌幽灵和菌落形成单位评价遗传灭活率。