轴向的

The flow field model of port plate pair in condition of the linear axial pressure distribution and dynamic model of flow divider pintle supporting system in abruptly variable load were established. Based on the two models, the balancing characteristics of flow divider pintle in ball piston pump was investigated.

在轴向压力线性分布的条件下，建立了配流副的流场模型，同时建立了配流轴支承系统在突变载荷下的动态仿真模型，在此基础上对球塞式液压泵配流轴的平衡特性进行了研究。

Thirdly, mathematic model of flowing fluid will be established in both radial gap and axial gap, and the pressure distribution laws will also be concluded in these two gaps.Fourthly, pressure distribution drawing will be made in entrance and cover board of pumps and axial gap of balance device.

为了分析新型轴向力平衡装置间隙的内部流动，建立了径向间隙和轴向间隙内部的流动数学模型，并应用粘性不可压缩流体的纳维—斯托克斯方程和流体的连续性方程，推导出了两间隙进出口压力差和泄漏量的关系式，进而得出平衡装置间隙内部的压力分布规律。

A washer has a body having an axis and provided with a first bearing face surface located at one axial side and adapted to cooperate with a nut, a second bearing face surface located at an opposite axial side and adapted to cooperate with an object, at least one third turning resistant surface adapted to cooperate with a thread of the bolt, the body having at least one resistive point arranged so that when the nut is turned and turns the bolt the body of the washer stops the bolt from turning and thereby the nut creates a pull on the bolt which elongates the bolt in an axial direction and applies to the body of the washer an axial force which overcomes the at least one resistive point so that a portion of the body of the washer is allowed to be pulled axially when the bolt elongates.

一种放在螺帽与物体之间的垫圈，螺帽与螺栓螺纹连接，螺栓插入在包括两个装配的部件的物体内，垫圈具有主体，和设有第一支承面表面，位于一个轴向侧面和与螺帽配合，第二支承面表面，位于相对的轴向侧面和与物体配合，以及至少一个第三转动阻力表面，与螺栓的螺纹配合，从而使螺帽以给定的扭矩在一个方向转动同时垫圈的主体沿相对方向接收给定的力时，仅有螺帽转动，以紧固或松开螺栓，而垫圈的主体和螺栓保持静止。

The flow of Non-newtonian fluid in eccentric annuli with the inner cyinder moving axially and it's application in preventing pumping rod and oil tube from eccentric wear in a polymer-driving well are studied in this paper.

在采油过程中，由于油井较深的缘故，抽油杆在油管中是处于偏心位置的，聚驱井产出液在抽油杆做轴向运动的井筒中的流动问题就是非Newton流体在内管做轴向运动的偏心环空中的流动问题。

The simulation results shows that when the hydroforming for real axle housing needs two bulge processes and the specific value of the two bulge ratio is about 1, the result is the best one; To obtain an appropriate route of loading force need adjust internal pressure and axial compression force for many times and according to the failure, the size of the two forces which has been mentioned can be rapidly and rationally adjusted; Because of good greasing conditions influencing largely, reducing the friction between tube blank and die inside surface as well as possibly not only makes more materials flow into the bulge area but effectively diminishes the axial compression force; The good or bad characteristics of tube blank material is also one of the decisive factors and when material is selected, we first consider its' formability.

模拟结果表明，当后桥壳需要两次进行胀形，两次胀形比比值约等于1时，胀形结果最好；合适的加载路径要经过多次调试，能根据胀形缺陷对内压力和轴向力的大小进行迅速地合理调整；良好的润滑环境对后桥壳液压胀形的影响巨大，要尽量减小管坯与模腔内壁的摩擦力，不但使更多的材料流入胀形区，而且能有效的降低轴向力的大小；管坯材料性能的好坏也是影响胀形的决定性因素，选材时首先要考虑材料的成形性。

The computationresults show that for a organ-pipe nozzle with a given configuration size, the nondimensional axial velocity attenuates slower with the increase in stand-distance, and the nondimensional axial velocity attenuation pattern remains the same, and the nondimensional axial velocity along the jet centerline attenuates slower with the increase in distance between the nozzleexit and the impinging plate.

计算结果还表明：对给定结构尺寸的风琴管喷嘴，随着喷距的增加，沿径向的无因次轴向速度衰减变慢、沿径向无因次轴向速度衰减规律不随喷速的变化而变化；无因次轴心速度的衰减规律随着喷嘴出口到井底间距离的增大，射流轴心速度衰减变慢，但其变化幅度不大；在固定靶距情况下，无因次轴心速度衰减规律不随喷速的变化而变化。

The effects of such parameters as temperature, pH, feeding rate,concentration, [NH_3]_T/_T molar ratio, surfactants and agitation, on the morphology and size of the particles, were studied and conclusions obtained are as follows:(1) The morphology and size of the particles are mainly decided by the species of nickel oxalates present.(2) Speeding up dissolution-recrystallization process benefits the preparation of the particles of being composed of a single species with uniform morphology and high aspect ratio.(3) The variations of nucleation and growth supersaturation under different conditions have definite effects on the morphology and size of the particles.(4) Adding PVP25 at a proper amount is beneficial to the preparation of fibrous nickel oxalate particles with high aspect ratio. 3 The formation mechanism as well as the morphology and size control of fibrous cobalt oxalate particlesThe cobalt oxalate particles with fibre morphology were prepared using CoCl_2 solution and mixed(NH_4)_2C_2O_4, NH_3·H_2O solution by a double jet process.

研究了温度、pH值、加料速度、浓度、[NH_3]_T/_T摩尔比、表面活性剂及其添加量、搅拌等对颗粒形貌与粒度的影响，主要结论为：(1)草酸镍化合物种类是决定颗粒形貌与粒度的最主要因素；(2)提高陈化中溶解—再结晶速度，有利于得到物相单一，形貌规整，轴向比大的粉末；(3)不同条件下，颗粒形核与生长过饱和度改变，也会对粉末形貌与粒度产生一定影响；(4)适量添加PVP25有利于大轴向比纤维状草酸镍的制备。3纤维状草酸钴的形成机理及其形貌与粒度控制采用CoCl_2溶液与(NH_4)_2C_2O_4和NH_3·H_2O混合溶液并流加料合成的方法，研究了纤维状草酸钴的制备。

The experimental and analytical results show that the axial rigidity of the corrugated pipe is 23.0 percent of the bare pipe with the same thickness and diameter,and the thermal compensation performance of the former is 2.27 times the latter's under equal-stress condition.By using corrugated pipe bundle instead of the bare pipe bundle with the same stiffness as its tube sheet,the axial thermal compensation can be increased by 40.4 percent,and the corresponding pulling-out force is 53.2 percent of that of the bare pipe bundle.

研究结果表明，波节换热管单管的刚度为相应光管的23.4%；在最大应力相同的条件下，波节换热管的轴向热补偿量为相应光管的2.27倍；在光管管束与壳体等刚度条件下，用波节管管束代替光管管束，轴向热补偿量可提高40.4%，相应的拉脱力为光管管束的53.2%。

These will provide theoretical guides for the design and the exploit of new products; By means of tensile testing of large number of the bi-axial warp-knitted fabrics, this paper delineated the inherent law of tensile properties especially in the relationships between the ground structures, materials and the fabric tensile properties; This paper also explained the problems existing in the domestic testing standard and measurement method of the warp-knitted grid products.

这个理论模型将为经编双轴向立体骨架织物的性能设计及生产提供很好的理论保证；本文通过对大量经编双轴向立体骨架织物拉伸性能的测试，了解掌握了该类织物拉伸性能的内在规律，为该类织物的性能设计打下了坚实的基础。

The thread tension mechanism is equipped with a pushing side thread tension board and a clamp axes pushed by the clamp board, a bearing hole is formed on the clamp base along the axial direction penetration.

所述夹线装置具有安装推压侧夹线板及被推压侧夹线板的夹线轴，在夹线座上形成沿夹线轴的轴向贯穿的轴承孔。

This one mode pays close attention to network credence foundation of the businessman very much.

这一模式非常关注商人的网络信用基础。

Cell morphology of bacterial ghost of Pasteurella multocida was observed by scanning electron microscopy and inactivation ratio was estimated by CFU analysi.

扫描电镜观察多杀性巴氏杆菌细菌幽灵和菌落形成单位评价遗传灭活率。