轴向流动

Results show the axial gap L has great influence on the flow unsteadiness in the rotor.

结果表明，轴向间距L对转子内流动的非定常性有着强烈的影响。

The axial dispersion coefficients and total mass transfer coefficients of xylose and sorbinose have been determined by stimulate response,technique with intert substance being traced.

实验结果表明，在低浓度下相平衡关系为线性；同时从时间域法处理实验数据的结果看出，随着流动相的流速加大，轴向扩散系数和时间总传质系数亦相应增

The results of this study indicate that changing the angle of the intake port has a profound effect on the flow field during the intake stroke of the engine cycle. For the case with the intake-exhaust valves canted at zero degree (the so-called vertical valves), the tumble ratio, swirl ratio, turbulent intensity, and turbulent kinetic energy in the direction perpendicular to the bisecting plane of the cylinder are at their highest levels than those obtained for the other cases. This effect is most pronounced after the compression stroke of the cycle. As a result of this study, it is observed that the behavior of the overall flow field from the intake to the completion of compression stroke has a major impact on the effectiveness of the mixing of fuel-air prior to the ignition of the engine cycle.

结果显示，改变进排气阀的倾斜角度对进气期间的流场变化有很明显的影响，其中以垂直阀(进排气阀倾斜0度)所得的 Y轴向(Y方向系垂直於将汽缸对分为二平面的方向)滚流强度、涡漩比、紊流强度、紊流动能等流场强度为最强；若以流体经活塞压缩后的流场特性进行探讨，所得结果显示压缩冲程对汽缸内流场的效应是不容忽视的；因此由进气到压缩过程结束的整体流场现象，才是影响引擎点火前的油气混合程度与燃烧品质的关键。

Numerical simulation on enhancement of axial heat conduction of laminar oscillatory flow in parallel plate channel is conducted.

本文对平板通道振荡流动强化轴向导热现象进行了数值模拟。

By using volume control method, the basic equations of axial laminar flow for power law fluids in eccentric annuli was seperated and sovled by ADI method.

利用控制体积法对幂律流体偏心环空轴向层流流动的基本方程进行了离散化处理，并用ADI方法进行了求解。

Combined hourglass control in analysis of cold ring rolling process;2. Recent status and development of real-time measurement and online control technology in cold ring rolling ;3. The influence law of feed rate of idle roll on the quality of end face of ring,axial width spread ratio,roll force,roll moment and metal flow characteristic in cold ring rolling process has been explored through the FEM numerical simulation of the ring with rectangular cross-section based on the elastic-plastic dynamic explicit FEM under the Abaqus software environment.

基于Abaqus/Explicit提供的显式动力学有限元算法，对矩形截面环件冷辗扩进行了有限元数值模拟，揭示了芯辊进给速度对环件冷辗扩过程中环件端面质量、轴向宽展率、辗扩力、辗扩力矩以及金属流动特性的影响规律，并从金属塑性成形原理和塑性加工力学等角度对这些规律进行了合理的解释，从而获得了进给速度对冷辗扩成形的影响规律，为环件冷辗扩在实际应用中进给速度的选择提供了依据，对揭示冷辗扩成形机理也具有十分重要的意义。

The influence law of feed rate of idle roll on the quality of end face of ring,axial width spread ratio,roll force,roll moment and metal flow characteristic in cold ring rolling process has been explored through the FEM numerical simulation of the ring with rectangular cross-section based on the elastic-plastic dynamic explicit FEM under the Abaqus software environment.

基于Abaqus/Explicit提供的显式动力学有限元算法，对矩形截面环件冷辗扩进行了有限元数值模拟，揭示了芯辊进给速度对环件冷辗扩过程中环件端面质量、轴向宽展率、辗扩力、辗扩力矩以及金属流动特性的影响规律，并从金属塑性成形原理和塑性加工力学等角度对这些规律进行了合理的解释，从而获得了进给速度对冷辗扩成形的影响规律，为环件冷辗扩在实际应用中进给速度的选择提供了依据，对揭示冷辗扩成形机理也具有十分重要的意义。

For the case of deep oil well, pumping rod is eccentric in oil tube during the oil recovery.

在采油过程中，由于油井较深的缘故，抽油杆在油管中是处于偏心位置的，聚驱井产出液在抽油杆做轴向运动的井筒中的流动问题就是非Newton流体在内管。。。

The flowfield numerical simulation of the axisymmetric jet emanating fromthe organ-pipe nozzle is made with the turbulence κ—ε two equations model, providing the basis for improving its cleaning ability.

采用湍流κ-ε二方程模型对风琴管式喷嘴内外流场进行数值模拟，弄清其流场的流动特性（轴向速度、径向速度的分布规律和衰减规律），为提高清除岩屑效率提供依据。

To reveal aft end internal flow feature of a solid rocket motor with submerged nozzle, a two dimension cold flow test model with rectangular channel was designed The cold gas simulation was based on geometric similarity and aerodynamic analogy Mean and fluctuating velocity field was measured using phase doppler particle analyzer It showed that the flow separates at upstream of the submerged nozzle and reattaches on the tip of the nozzle nose A relatively steady recirculation zone formed in...

为了揭示含潜入喷管的固体火箭发动机尾部流动特征，按照几何相近和气动相似原则设计了通道为矩形的二维冷流实验模型，利用相位多普勒粒子分析仪对燃烧室尾部气流的时均速度和湍流脉动速度进行了测量。实验结果表明气流在潜入喷管入口上游发生分离，再附点位于喷管前端部外侧，背壁空腔内形成一个较为稳定的回流区，流场的轴向和横向湍流强度都比较大

This one mode pays close attention to network credence foundation of the businessman very much.

这一模式非常关注商人的网络信用基础。

Cell morphology of bacterial ghost of Pasteurella multocida was observed by scanning electron microscopy and inactivation ratio was estimated by CFU analysi.

扫描电镜观察多杀性巴氏杆菌细菌幽灵和菌落形成单位评价遗传灭活率。