轴向流动

The numerical simution results show that there is slug flow in the plunger-cylinder of the annulus pipe,because of the existence of Casson yield stress.

数值研究结果表明，由于Casson屈服应力的作用，轴向同心环空内存在柱塞流动，柱塞的大小与Casson屈服应力成正比，与压力梯度成反比。

It is governed by the equation of continuity and momentum for the liquid in cylindrical coordinates with axial symmetry, the isentropic equation of state for water.

曲面头部的水弹高速冲击刚性表面的流体动力学问题，可以归结为无粘性、可压缩的不定常流动问题，受轴向对称园柱座标的连续和动量方程、水的等熵状态方程支配。

Off-design flow field analysis and radial force prediction of centrifugal pump

合成气在催化剂床层内的流动方向既有轴向，又有径向。

The effects of different parameters and cross-sections on axial velocity, the distribution of secondary flow, temperature field, turbulent kinetic energy, wall friction coefficient and wall Nusselt number are analyzed in detail.

详细分析了充分发展的和发展段的湍流管道内，不同截面形状和几何参数对轴向速度分布，截面二次流结构，湍动能，曲线管道摩擦比，温度分布和曲线管道Nusselt系数比等管道流动和传热特性的影响。

ABSTRACT Since the pioneering reports by Filippov in 1959-1962, there have been a large number of publications on magnetofluidized beds , that is, fluidized beds of magnetizable particles under the influence of an external magnetic field.

磁稳定床是在轴向、不随时间变化的均匀外加磁场作用下形成的稳定床层；它是不同领域知识（磁体流动力学与化学反应工程）结合形成的新构思。

Support has been provided for that annulus fluid instances were numerical simulated with PHOENICS, PHOENICS is used to set up a numerical model of power-law fluid in a concentric annulus flow, by comparing the numerical simulation results for the axis velocity of the power-law fluid in a concentric annulus flow with two dimensional PIV experimental results.

为应用PHOENICS数值模拟环空管道内其它流体情况提供借鉴，利用PHOENICS建立幂律流体环空流动的数值模型，将同心环空幂律流体轴向速度数值模拟结果与二维PIV实验结果对比。

The general model, including axial dispersion flow for the bulk fluid phase, diffusion equation described by Fick law for the particle phase and the equilibrium concentration given by a modified competitive Langmuir isotherm, was presented and discretized with Galerkin and orthogonal collocation into a series of ordinary differential equations.

为考察孔内扩散对模拟移动床分离过程的作用，采用综合速率模型对其进行研究，其中流动相模型为轴向扩散活塞流，颗粒相为Fick定律描述的扩散方程，液相和固相之间的吸附平衡采用改进的Langmuir吸附等温线。

Generally, it can be divided into three types of floating stress, spindling stress and pressing stress, among which floating stress is the most important.

血管内流体压力的突然升高，在血管分叉处产生涡流；液体在血管内流动对管壁产生不同的应力，一般分流体切应力、轴向应力和压应力3种，其中流体切应力最为重要。

Experimental study was conducted on flow characteristics of catalyst in a standpipe with f108 mm4 mm and height of 10 m.

对垂直立管中催化剂的流动性能进行了实验研究，测定了各种操作条件下立管中的轴向压力分布、催化剂循环速率以及附加吹气的影响。

The effect of curvature, torsion and Dean number on secondary flow, the isoline of stream function, the distribution of axial speed and wall friction is discussed in detail.

详细讨论了曲率、挠率、Dean数对二次流动、流函数等值线和轴向速度的分布以及壁面摩擦力的影响。

This one mode pays close attention to network credence foundation of the businessman very much.

这一模式非常关注商人的网络信用基础。

Cell morphology of bacterial ghost of Pasteurella multocida was observed by scanning electron microscopy and inactivation ratio was estimated by CFU analysi.

扫描电镜观察多杀性巴氏杆菌细菌幽灵和菌落形成单位评价遗传灭活率。