轴向场

In the study of microwave sintering of BaTiO〓 PTC ceramics, when the applied microwave power are above than a certain value, the abnormal axial shrinkage of the sintered sample will occur, by the analysis of SEM and XRD, it is found the microstructure and phase are different with conventionally sintered sample, the reason for this phenomenon is due to orientational grain growth by the action of electric field in the microwave sintering process.

微波烧结BaTiO〓电子陶瓷时，当所加的微波功率超过一定值时，首次发现烧结样品出现轴向异常收缩现象，采用SEM、XRD等分析发现其微观结构与常规烧结有巨大的差异，这是BaTiO〓材料的晶粒在微波场中受电场力作用而发生的取向生长造成的。

An iterative temperature field model of cylinder, in which the non-linear steam temperature distributed along axial direction, was got based on two-dimensional transient heat conduction differential equation. Analytical simulation demonstrates not only a rapid solution convergence but a minor error.

在二维圆筒壁非稳态导热的基础上，得到了圆筒壁内蒸汽沿轴向线性分布，随时间非线性变化的温度场迭代计算公式，并与有限元计算结果作了对比，结果表明所得模型计算精度高、计算速度快。

The velocity distribution of the numerical simulation and the theoretical equations calculation are compared on the condition of axial symmetry.

结果表明，在轴对称条件下，对数模、理论计算的速度分布进行对比分析，证实了旋涡流场不仅是径向的函数，而且还是轴向的函数。

Furthermore, the effect of axial stretch and temperature on the deformation is discussed.

同时，讨论了轴向拉伸和温度场对圆筒变形的影响。

Whispering-gallery-mode laser was observed in the cylindrical microcavity by evanescent wave exciting and coupling dye gain.

采用近轴向消逝波抽运的方法，使激光的染料增益局限于抽运光在染料区的消逝场范围内，极大地提高了消逝波耦合柱形微腔的抽运效率。

The propagation of elastic wave in a cylindrical bore hole containing a fluid (for example, the muddy fluid is generally used) for acoustic logging is analyzed with a simplified model.

本文分析了简化模型下声波测井时裸眼井中弹性波的传播，此波场可看成是轴向传播有不同波矢的分波的叠加。

The structure and the performance of the single screw extruder of electromagnetism dynamic are presented.

简要介绍了电磁动态单螺杆挤出机的结构性能，分析了螺杆在振动力场作用下的轴向受力状况。

According to the interaction between the cutting grains and the liquid medium, integrating the theoretic analysis with experiments, and referencing the experimental formula, the sedimentation law of cutting grains in the dynamic solid/liquid separator by compressing and filtering is discussed. The theoretical exploration and research are conducted on the grain-forcing situation, axial sedimentation, sedimentation in the centrifugal force field etc., and the final sedimentation velocity of the cutting grains is obtained in the separator.

文章从岩屑颗粒与液相介质之间的相互作用入手，采用理论分析和试验研究相结合的方法，参照经验公式，讨论了固液动态压滤分离机中岩屑颗粒的沉降规律，对动压机内颗粒的受力情况、轴向沉降、离心力场沉降等问题进行了理论探讨和研究，得出了岩屑颗粒离心沉降末速度。

In order to solve torsional deflection strength of transformer's spiral winding, the axial current effect on radial magnetic field is analyzed.

针对变压器螺旋绕组扭转变形强度问题，就轴向电流分量对辐向磁场的影响进行了分析，从而为进一步进行大型变压器瞬态涡流场的数值计算提供了依据。

Then, the distribution of tangential, radial, axial components of velocity and pressure is given.

同时得到了流场内部切向速度、径向速度、轴向速度及压力分布规律。

The split between the two groups can hardly be papered over.

这两个团体间的分歧难以掩饰。

This approach not only encourages a greater number of responses, but minimizes the likelihood of stale groupthink.

这种做法不仅鼓励了更多的反应，而且减少跟风的可能性。