轴向

Kinematics model of elastic rubber parts, first is the simplified three vertical springs 22, in which an alternative to rubber axial deformation, and the other two vertical springs alternative to radial deformation of rubber parts.

弹性运动学模型中首先是橡胶件简化成三根两两垂直的弹簧，其中一根替代橡胶件的轴向变形，另两根垂直的弹簧替代橡胶件的径向变形。

In the end, stress distribution at the connection position and distribution of contact pressure on the thread teeth are deduced by applying equivalent contact pressure.

通过变形协调原理，求出了轴向力沿接头螺纹牙的大小分布，进而求出了上扣、内压和拉伸工况综合作用下的等效接触压力。

In this modified model, the effect of the stress concentration on the end stress in the fiber end region is considered, the average matrix strain is used to substitute for the so-called far field strain in the previous shear lag model. The change of the deformation states from elasticity to plasticity is considered and the interfacial shear stress and fiber axial stress are derived.

修正的模型合理考虑了纤维根区域应力集中对根应力的影响；用基体平均应变代替了经典剪切滞后模型中的远场应变；考虑了基体变形状态从弹性到塑性的变化，给出了塑性区上的表面剪切应力和纤维轴向应力的表达式。

Velocity distribution of fluid in eccentric annuli with the inner cylinder reciprocating axially［J］.

流体在内管做轴向运动的偏心环空中的速度分布［J］。

By using volume control method, the basic equations of axial laminar flow for power law fluids in eccentric annuli was seperated and sovled by ADI method.

利用控制体积法对幂律流体偏心环空轴向层流流动的基本方程进行了离散化处理，并用ADI方法进行了求解。

Thus the on-axial polarization distribution can be controlled by apertures,which is useful for the application of partially coherent light.

利用光阑可对部分相干光的轴向偏振传输特性进行控制，对实际应用有重要的参考价值。

The spray characteristics of three configurations of effervescent atomizers are measured in detail by the MF laser-scattering-analyzer, showing the effects of airliquid ratio, available pressure drop, atomizer geometry and axial distance from exit of atomizer.

这些结果显示了气液比，气液供应压降、喷嘴几何参数、混合腔压力、喷嘴轴向距离等因素对气泡雾化喷嘴喷雾特性的影响。

The ROM of L5-S1 segment was significantly increased in flexion, left and right lateral bendings (relative ROM 1. 57, 1. 43, 1. 61 seperatively).

双侧小关节内侧1/2切除和双侧小关节全切除状态之间在右轴向旋转运动方面有显著性差异。

M were applied to produce six kinds of pure moment of force and to create six kinds of movement of the lumbar spine in flexion, extension, left and right lateral bendings as well as left and right axial rotations.

在双侧小关节分级切除状态下，后路螺纹椎间融合器均能显著降低L4-L5节段的前屈、左右侧弯运动范围，但后伸、左右轴向旋转运动只能恢复到完整状态水平。

After discectomy, partial laminectomy and bilateral medial 1/3 facetectomy, the ROM of L4-L5 segment was significantly increased in flexion, extension, left and right lateral bendings as well as left and right axial rotations (relative ROM 1. 34, 1. 94, 1. 19, 1. 34, 2. 23, 1. 52 seperatively).

随着双侧小关节逐级切除，各组运动的运动范围明显呈逐渐增加趋势，双侧小关节内侧1/3切除和双侧小关节全切除状态之间在前屈、左右侧弯、左右轴向旋转运动方面有显著性差异。

This one mode pays close attention to network credence foundation of the businessman very much.

这一模式非常关注商人的网络信用基础。

Cell morphology of bacterial ghost of Pasteurella multocida was observed by scanning electron microscopy and inactivation ratio was estimated by CFU analysi.

扫描电镜观察多杀性巴氏杆菌细菌幽灵和菌落形成单位评价遗传灭活率。