轴向

It is suggested that the axial location clearance of bearing outer ring should be minimized provided the assembly reliability can be reached.

对於采用卡环定位轮毂轴承，在满足可靠装配条件下，应尽可能减小轴向的配合间隙。

It is suggested that the axial location clearance of bearing outer ring should be minimized provided the assembly reliability can be reached.

对于采用卡环定位轮毂轴承，在满足可靠装配条件下，应尽可能减小轴向的配合间隙。

AFTER THE OWNERSHIP TRANSFER,IN ORDER TO STRENGHTEN THE MANUFACTURING CAPABILITY,THE COMPANY PURCHASED MANY NEW EQUIPMENTS LAST YEAR,THERE ARE CNC LINE CUTTING MACHINE,CNC STATOR COIL WINDING MACHING,CNC SPOT WELDING MACHINE,BELT SAW CUTTING MAHCING,HEATTREATMENT MODIFIED EQUIPMENT,500T FUEL PRESSER,CNC LATHE,STATOR AND ROTATOR LIQUER IMMERSION AND DRYING PRODUCTION LINE,SINGLE BOLT PRESSER,ARMATURE PRODUCTION LINE,STARTER ASSEMBLY AND TESTING LINE,LIQUER SPRAY PRODUCTION LINE,GERMANY TOX COMPANY PUNCHING AND CONNECTING FACILITY AND GERMANY NUT FASTENING FACILITY,AND WE ALSO PURCHASE THOSE ADVANCED TESTING FACILITIES SUCH AS THE DOMESTIC MOST ADVANCED COMPREHENSIVE TESTING UNIT,THREE DIRECTION HIGH AND LOW TEMPERATURE CHANGE AND VIBRATION TESTING UNIT,HIGH TEMPERATURE TESTING BOX.

企业转制后，为提高产品制造能力已购置生产设备：数控线切割、数控定子绕线机、数控点焊机、带锯床、热处理调质设备、500吨油压机、数控机床、定子、转子浸漆干燥线、单螺杆空压机、电枢生产线、起动机总装及试验线、喷漆线、德国TOX公司冲压连接设备和德国的螺栓紧固设备。试验设备：购置目前国内最先进的起动机综合试验台、三轴向高低温交变振动试验台、高温试验箱等试验设备。

Both monotonic axial compressive and axially loaded cyclic tests have been carried out on the steel box brace used in New CCTV Building to investigate the effect of assembling welds including full penetration and partial penetration on the structural behavior of the brace.

为考察全熔透和部分熔透两种组装焊缝形式对箱形截面钢支撑受力性能的影响，本文对中央电视台新台址建设工程中的箱形截面支撑进行了单调受压、轴向反复拉压试验；同时，采用ABAQUS有限元软件实现了对部分熔透试件未熔透处的接触模拟和滞回性能模拟。

Actually, downhole casing is cemented at its bottom, and fastened by casing head at its top, so the axial tension caused by internal pressure does is not loaded by the casing, instead, by well bottom and the casing head, etc..

实际井下套管下端被水泥固定，上端被套管头固定，此时套管承受内压所产生的轴向拉力，并不作用在套管上，而作用在井底和上端约束上。

Under high pressure of the filter chamber and high flux,the differences have the tendency to become larger.

这种压力和孔隙速度沿轴向分布的差异，会对陶瓷过滤元件的

Numerical simulation on enhancement of axial heat conduction of laminar oscillatory flow in parallel plate channel is conducted.

本文对平板通道振荡流动强化轴向导热现象进行了数值模拟。

On the basis of researching sealing pipeline joint structures with double-cone pipe union in depth, this paper used the method of Robust Design, synthesized the mainly factors such as geometrical sizes of components, mechanical property of material, surface roughness of components, axial preloading force, fit clearance, taper and the difference of taper etc., and obtained a set of design rational parameters.

本文在深入研究双锥形管接头密封管路联接结构的基础上，运用稳健设计方法，综合元件几何尺寸、材料力学性能、元件表面粗糙度、轴向预紧力、配合间隙、锥角和锥角差等因素，找出了该结构比较合理的设计参数组合。

Disk rotation balance week, will go to a certain point of view, the local emergence of the greatest axial clearance or minimum clearance space.

平衡盘转动一周，会在转到某一角度时，局部出现轴向间隙的最大间隙或最小间隙。

In regard to the practical coking process, a kinetic two-dimension coordinate calculation method was established in determination of the temperature field and its stress field of coke tower shell both in radial and axial directions with reference to shell innate flow rate by FEM.

通过动态坐标法模拟了恒速上升的液体介质界面在焦炭塔内沿塔壁爬升的动态边界工况，对其在壁中引起的径向和轴向二维瞬态温度场进行了有限元计算。

This one mode pays close attention to network credence foundation of the businessman very much.

这一模式非常关注商人的网络信用基础。

Cell morphology of bacterial ghost of Pasteurella multocida was observed by scanning electron microscopy and inactivation ratio was estimated by CFU analysi.

扫描电镜观察多杀性巴氏杆菌细菌幽灵和菌落形成单位评价遗传灭活率。