轴向

A study in form and geometry, the plaza continues the form language of the axial connection and extrudes it into the third dimension through the addition of precast concrete seat walls set in plinths of decomposed granite and surrounded by mixed understory plantings.

研究的形式和几何，继续在广场的形式语言和挤出轴向连接到第三个层面通过增加预制混凝土墙壁座位设置在plinths的风化花岗岩，四周是混合林下种植。

Compared with symmetric corner filleted flexure hinge, the performance of flexure hinge can be evaluated in terms of flexibility, precision of rotation and sensitivity to axial effects. Experiment results can provide some theoretic foundations for flexure hinge design.

对单边导角形柔性铰链的性能进行分析，得出了结构参数对其柔度性能的影响关系，并通过与双边导角形柔性铰链比较，分析了单边导角形柔性铰链的转动能力、转动精度和对轴向载荷的影响，为柔性铰链在结构紧凑、大位移场合的工程应用提供了有价值的参考。

Based on the optoelectronic inspecting technology, the chinks between knife edge and the generatrices of measured part were measured by the laser scanned inspecting system and using the rotating and axial feed servo systems, and the non contact automatic measurement of straightness error was realized.

基于光电检测技术，利用回转和轴向进给伺服系统，通过激光扫描检测系统测量刀口尺与被测零件素线之间的间隙，实现了对直线度误差的非接触自动测量。

The behaviour of these bolts, when fully grouted in resin, was investigated under axial and shear loading.

这些螺栓行为，当充分地填水泥在树脂，被调查了在轴向和剪装货之下。

In order to study the pressure-swirl nozzle's atomization characteristic, the particle diameter distributions along axis of the nozzle have been measured by immerging.

摘要为了研究一种高压静电压力旋转喷嘴的雾化特性，采用浸入法测量了该喷嘴喷雾雾滴粒径在喷嘴轴向的分布状况。

In this paper, axial tensile and interlaminated mechanical properties of glass fiber epoxy resin composites were studied by theoretical analyses and experiments.

本论文对玻璃纤维增强环氧树脂复合材料的轴向拉伸性能和层间力学性能进行了理论分析和实验研究。

The distribution and variation of plastic zone in the joint were calculated and analyzed during inertia friction welding process. And the variation of deformation rate of plasticized material was also simulated.

计算并分析了惯性摩擦焊接过程中接头塑性区的分布、扩展规律及其与工件轴向缩短的关系，并计算了塑性区金属塑性变形速率的分布和变化情况。

The corres- ponding computer program is also developed and has been used to work out a series of problems with satisfactory results.

文(8)建议最小二乘意义下的近似方法，目的是使连接点处两单元轴向位移差的平方泛函取极小，但是对二维及三维的薄壁杆件体系

Numerical simulations showed the axial velocity in the precessing flow were decreased significantly because of the entrainment of ambient air. The swirling motion, the wall attachment effect and the reverse flow were also found in the numerical flow field. It is shown that the simulation results of the precessing jet flow accord well with the analysis and the previous work.

数值模拟表明旋进射流的轴向流动速度衰减得很快，流场中存在明显的旋流、附壁效应和反向回流现象，所得到的结果与已有的分析结论基本吻合。

For internal high pressure forming of a hollow part with big difference on section perimeter, the problems of axial feeding and preforming are necessary to be solved to produce qualified parts with more uniform thickness distribution.

截面周长差较大的空心零件的内高压成形需要解决膨胀区的轴向补料问题和预成形问题，才能获得壁厚分布较为均匀的合格零件。

This one mode pays close attention to network credence foundation of the businessman very much.

这一模式非常关注商人的网络信用基础。

Cell morphology of bacterial ghost of Pasteurella multocida was observed by scanning electron microscopy and inactivation ratio was estimated by CFU analysi.

扫描电镜观察多杀性巴氏杆菌细菌幽灵和菌落形成单位评价遗传灭活率。