轴向

The fixator with the highest axial stability did not result in the highest failure moment.

该最高轴向稳定的固定器没有在最高失败时刻致成。

Axial distribution of gas holdup;inflection point of gas holdup;frother dosage

气含率轴向分布；气含率拐点；起泡剂用量

In this dissertation, we purify,functionalize, and align the single-walled carbon nanotubes by Langmuir-Blodgett technique using compression-transfer method.

本文正是针对这一问题，对单壁碳纳米管进行了提纯、功能化，并利用LB技术的液面排布转移法实现了碳纳米管沿着轴向大面积定向排列。

They showed the highest tensile strength and thermal conductivity, and can be semi-conductive or metallic depending on how the graphitic sheets are rolled up.

它们具有最高的轴向强度和导热系数，并且随着石墨层片卷曲方式的不同，既可以是导体，也可以是半导体。

In the expariment,18 pieces of moist fresh humeri were used.Results Inpull and compress test,the high level of break load of BLIN was close to that ofboth-ends transverse-interlocking intramedullary nail.

采用18根湿润新鲜肱骨标本进行实验，比较分叉交锁髓内钉与其它三种内固定物固定之肱骨骨折在抗轴向拉伸及压缩、抗弯曲、抗扭转的强度和刚度等方面的差异性。

The finite element analysis of an existed hydroturbine thrust bearing support are presented in the paper.

本文对水轮机推力轴承支架进行了有限元分析，为改善应力分布、减小轴向位移和节省材料，对其作了优化设计

OBJECTIVE: To quantify the stress distribution on the intervertebral disc, interarticular process and iliolumbar ligament of the lumbar vertebrae.

目的：观察轴向载荷下L5~S1上关节突与下关节突之间的峡部、椎间盘和髂腰韧带的应变和表面应力情况。

RESULTS: Under the axial loading on the intact specimen, 70% stress contributed at the pars, 26% at intervertebral disc, and 2.8% at iliolumbar ligament.

结果：正常标本轴向压缩实验，70.7%的应力分布于峡部，分布在椎间盘应力为26.5%，而髂腰韧带则有2.8%应力分布。

Incurrent research, aiming at the rupture problem engendered in the shooting process of acertain 5.56mm automatic rifle, the strain and stress distributions on the cartridge caseunder the action of axial pull have been analyzed. Based on the theories of elastic-plasticmechanics and contact mechanics, a mathematic and physical model of the cartridge-caseand chamber system has been set up; and based on the platform of the general softwarepackage APDL of ANSYS for finite element analysis, a parameterized model of thecartridge-case and chamber system has also been established. The method for nonlinearFEA has been adopted to analyze the stress distribution on the entire cartridge-case andchamber system, and the method of contact element has been employed to investigate thecontact stress between the cartridge case and chamber, and then the influences of frictioncoefficient and locking space on the static and dynamic stress and strain response of thecartridge case and chamber to the action of power gas have also been discussed. On thebasis of a lot of numerical tests, a kind of element Plane13, which is concentrated incoupled computation of heat and construction, has been used finally to simulate thetransient response of the cartridge-case and chamber system to the power gas. Throughloading the temporary thermal characteristics of explosive gas in the procedure of emulate, the corresponding transient thermal stress distributed on the entire system under thecombined load of transient thermal stress and transient pressure has been obtained. Owingto these comprehensive considerations, the numerical results obtained in this paperrepresent the actual situations comparatively exactly.

本文针对某5.56mm自动步枪在工作中出现断壳的问题，分析了弹壳在轴向拉力作用下的应力应变；基于弹塑性力学及接触理论，建立了弹壳弹膛系统的数学、物理学模型，在通用有限元ANSYS软件的参数化建模工具APDL平台上，建立了弹壳弹膛系统的参数化模型；采用非线性有限元法计算了弹壳弹膛系统的整体应力，引入接触单元法分析弹壳和弹膛的接触压力，探讨了在不同的摩擦系数和不同的闭锁间隙对弹壳弹膛静、动态响应的影响；本文进行了大量的尝试，最后确定采用热、结构耦合单元Plane13，在计算中加载了火药气体的温度历程，成功的获得了弹壳弹膛系统在瞬态的热载荷和瞬态的压力载荷同时作用下弹壳弹膛系统的热应力数值解，考虑因素全面，比较真实的反映了弹壳弹膛系统在火药气体压力和热载荷下作用的情况。

Two qina ligands chelate a cobalt ion by 0 and N atoms and two DMSO ligands coordinate a cobalt ion by two O atoms at an axis. The complex formed inerratic octahedron configuration, and π-π stacking weak interaction was observed between the molecules.

配合物为单斜晶系，P2(1)/C空间群，2个qina配体以氮原子和氧原子与Co离子螯合配位，2个DMSO以氧原子与Co离子轴向配位，形成规则的八面体构型配合物，分子之间存在π-π堆积弱相互作用。

This one mode pays close attention to network credence foundation of the businessman very much.

这一模式非常关注商人的网络信用基础。

Cell morphology of bacterial ghost of Pasteurella multocida was observed by scanning electron microscopy and inactivation ratio was estimated by CFU analysi.

扫描电镜观察多杀性巴氏杆菌细菌幽灵和菌落形成单位评价遗传灭活率。