轴向

Figure 2 is a plot of azimuthally averaged and timeaveraged radial solids holdup distribution, measured at four axial locations, at a liquid

图2 是在20 cm/s的液体超临界流速下4个轴向位置测得的对数平均化和时间平均化的径向固体含率分布图。

The study has also shown that there is a rotation angle for azimuthally NMO velocity ellipses in monoclinic media which different form HTI and orthorhombic media. The rotation angles of NMO ellipses are related to the property of fracture infill, fracture density ratio and the angle between the two fractures. These research results can be used to identify the type of fractured media and the property of fracture infill.

同时，研究表明对于裂隙型单斜各向异性介质，其方位NMO速度椭圆轴向并不象HTI介质和正交介质中的那样与自然坐标系的坐标轴一致，而是发生了一定角度的偏离，其大小与裂隙填充物的性质、两组裂隙密度的比值及裂隙间的夹角等因素有关，研究结果为进一步区分裂隙介质的类型及裂隙填充物的性质提供依据。

The study has also shown that there is a rotation angle for azimuthally NMO velocity ellipses in monoclinic media which different form HTI and orthorhombic media. The rotation angles of NMO ellipses are related to the property of fracture infill, fracture density ratio and the angle between the two fractures.

同时，研究表明对于裂隙型单斜各向异性介质，其方位NMO速度椭圆轴向并不象HTI介质和正交介质中的那样与自然坐标系的坐标轴一致，而是发生了一定角度的偏离，其大小与裂隙填充物的性质、两组裂隙密度的比值及裂隙间的夹角等因素有关，研究结果为进一步区分裂隙介质的类型及裂隙填充物的性质提供依据。

Of bidentate ligand DABCO is added exactly as axial ligand to the catalytic system.

以双齿配体DABCO作为轴向配体，双核铁双卟啉催化环己烷羟化反应

Driving system is one key of it, and it needs big torque and endures biggish shaft power.

传动系统是双螺杆磨浆机的关键部件，要求输出较大的扭矩，并承受较大的轴向力。

Research indicates that this drug not only biochemically interacts with cartilage and other tissues of the joints, but also increases concentration of joint lubricant.

因此，在重大的痛苦和跛足尽管存在负面结果在X射线，计算机轴向断层扫描或磁共振成像往往是成功的检测骨和由联合调查放射忽视异常。

When the burring process of 12×4J wheel is processed taking the deformation area as the plane stress condition,the deformation characteristics of normal and radius directions are studied,which is influenced by the factors such as height and the inner hole initial radius and the deformation law of circle strain.

利用斜冲模对12×4J轮辐进行翻边时，将变形区看做是平面应力状态，探讨了翻边高度、初始孔径及斜冲模角对翻边变形区径向应变和轴向应变的影响，对12×4J轮辐翻边不同斜冲模角下的冲压力变化规律进行了计算。

To reach the maximum load-carrying capacity, together with axial guidance in the very limited headroom available, SKF designed a cageless polymer track-runner ball bearing with two full-complement, asymmetric sets of stainless steel balls .

为了达到最大承载能力，以及轴向的指导非常有限的空间可用， SKF的设计了一个cageless聚合物跟踪亚军球轴承有两个完整的补充，不对称套不锈钢球。

The results show that upper bainite of 9Cr2Mo Steel and GCr15 steel is feathery and the upper bainite carbide is lamellar or claviform. The upper bainite carbide distributes between the subunits of bainite ferrites by and large parallelly to the axis of bainite ferrites. Lower bainite of 9Cr2Mo Steel and GCr15 steel is in bamboo leaf shape and the lower bainite carbide is in shred or fibre shape. The lower bainite carbide distributes between the bainite ferrites, furthermore, the angles between lower bainite carbonide and the principal axis of the lower bainite ferrites are unequal.

结果表明，9Cr2Mo钢和GCr15钢的上贝氏体组织呈羽毛状，上贝氏体碳化物呈长短不一的薄片状或短棒状，分布在铁素体亚片条或亚单元之间，其排列与贝氏体铁素体片条轴向大体上平行分布；下贝氏体组织呈竹叶状或针状，下贝氏体碳化物呈细片状或纤维状等形状，分布在铁素体片中间，大多数与片条的主轴方向交角排列，但角度不等。

The testing was performed under axial load(25N～150N) on each group. The stress changes of the caudad (C5/6,C6/7) zygapophyseal joint was tested .

结果 1。在轴向加载下，下位节段关节突关节内的压力随着施加载荷的增大而增大。

This one mode pays close attention to network credence foundation of the businessman very much.

这一模式非常关注商人的网络信用基础。

Cell morphology of bacterial ghost of Pasteurella multocida was observed by scanning electron microscopy and inactivation ratio was estimated by CFU analysi.

扫描电镜观察多杀性巴氏杆菌细菌幽灵和菌落形成单位评价遗传灭活率。