轴向

Research shows that the main factors influencing forging penetration efficiency are reduction in pass and the dip angle of the hammer, and the main factors influencing forged piece surface quality are axle feeding speed and rotation angle.

研究表明：影响锻透性的主要因素为道次压入量和锤头倾角；影响锻件表面质量的主要因素为轴向送进速度和旋转角度。

The stress and radial displacement will increase with the increment of half cone angle and lead.

螺旋输送器的最大应力强度和最大径向位移均与转速近似地成二次方关系；减小叶片壁厚，沉渣对螺旋叶片作用的正压力所引起的叶片的最大轴向位移增长较快；正常工况下，螺旋输送器的最大应力强度和最大径向位移都随着半锥角和导程的增加而增大。

The max stress and the max radial displacement of conveyor is also proportional to the square of rotational speed. With the decrease of the blade thickness, both the stress and axial displacement of conveyor increase rapidly. The stress and radial displacement will increase with the increment of half cone angle and lead.

螺旋输送器的最大应力强度和最大径向位移均与转速近似地成二次方关系；减小叶片壁厚，沉渣对螺旋叶片作用的正压力所引起的叶片的最大轴向位移增长较快；正常工况下，螺旋输送器的最大应力强度和最大径向位移都随着半锥角和导程的增加而增大。

The tortuosity can be described by bit weight in axial direction and the angle change of drill string bynormal can be considered as the torsion angle of the borehole.

弯曲主要体现为狗腿度，挠曲就体现为井眼的扭转。这种空间挠曲和弯曲特性可以通过测量轴向不受钻压作用的下部钻具组合的变形来描述。

Information about spatial variation of lower degree components of the geomagnetic field is contained in angular dispersion of VGP.

虚磁极的角散布携带着地磁场低阶非轴向偶极子分量空间变化的信息。

The results showed that the angular velocity was relevant to performance parameter of granular material and filling ratio.

从圆周运动和轴向运动两个方面分析混合发生时颗粒物料运动的模式及加料方式对混合效果的影响。

Manufacturing the contact cable by material composite technology is a newly developed method in recent years. Due to its anisotropism and excellent ability of interfacial combination, in-situ composite shows a wonderful potential to giving the attention to the strength and the conductivity of conductive materials at on time.

采用材料复合技术研制导电材料是近年来发展起来的新方法，由于自生复合材料的各向异性和良好的界面复合能力，使其在解决导电材料的轴向强度和导电性的综合性能方面表现出了极大的潜力。

And its axial displacement reflect the size of the motor are many anomalies.

而它的轴向位移的大小反映很多种电机的异常情况。

MAIN OUTCOME MEASURES: Stress images and peak stress of pedicle screws under lumbar axial compression, anteflexion, extension, lateral bending and rotation.

主要观察指标：椎弓根螺钉在轴向压缩、前屈、后伸、侧屈和旋转等各种生理载荷下的应力云图和峰值。

The displacement pick-up was put into C3/4 intervertebral space and axis pressure (0～160N) homolateral-bending (0～1.5Nm), oppositeside-bending (0～1.5Nm), back-extending (0～1.5Nm) and anteflexion (0～1.5Nm) were respectively loaded. After having measured the morphological changes of C3/4 intervertebral foramena in C5/6 intergrity group, discectomy group and replaced group, the changes in different groups were compared.

将位移传感器置入C3/4椎间孔内，在颈椎标本上施加轴向（0～160N）、同侧弯（0～1.5Nm）、对侧弯（0～1.5Nm）、后伸（0～1.5Nm）、前屈（0～1.5Nm）分级载荷，分别测量C5/6椎间盘完整组、C5/6椎间盘髓核摘除组和C5/6人工颈椎间盘置换组，C3/4椎间孔高度、宽度和ROV。

This one mode pays close attention to network credence foundation of the businessman very much.

这一模式非常关注商人的网络信用基础。

Cell morphology of bacterial ghost of Pasteurella multocida was observed by scanning electron microscopy and inactivation ratio was estimated by CFU analysi.

扫描电镜观察多杀性巴氏杆菌细菌幽灵和菌落形成单位评价遗传灭活率。