轴向

In the study of microwave sintering of BaTiO〓 PTC ceramics, when the applied microwave power are above than a certain value, the abnormal axial shrinkage of the sintered sample will occur, by the analysis of SEM and XRD, it is found the microstructure and phase are different with conventionally sintered sample, the reason for this phenomenon is due to orientational grain growth by the action of electric field in the microwave sintering process.

微波烧结BaTiO〓电子陶瓷时，当所加的微波功率超过一定值时，首次发现烧结样品出现轴向异常收缩现象，采用SEM、XRD等分析发现其微观结构与常规烧结有巨大的差异，这是BaTiO〓材料的晶粒在微波场中受电场力作用而发生的取向生长造成的。

In this thesis, the basic arithmetic of PIV software - cross-correlation arithmetic is introduced in detail, During the data process, through processing the two sequential images by the cross-correlation arithmetic, the vector charts of particles velocity can be obtained, so is the chart of absolute velocity, with velocity decomposed into the radial velocity and axial velocity.

本文对试验所获得的连续图像通过互相关算法，获得颗粒速度矢量图，并将速度分解为径向速度和轴向速度，对每一小区域内的颗粒按速度方向不同进行速度平均，获得颗粒的平均速度分布曲线。

An axial loading of 500 N was put to the model under bilateral acetabulum constraint.

模拟人体双腿直立位的生理姿势，对模型施加500 N轴向载荷。

Under optimal conditions, oxidation of ethylbenzene into acetophenone under 1 atm O2 and 1 mol% NHPI reach to 64% yield.

在最佳的催化状态下，苯乙烷能在1 atm的氧气、1 mol% NHPI与轴向配位基为吡啶的紫质修饰二氧化钛共催化下，氧化成苯乙酮，并得到64%的产率。

Comparing with the case of no adit, because of arch tunnel set being broken; the intersection structure is subjected to combination of complicated stresses including transverse stress, but not the axial stress.

与无横通道情况相比，由于拱形支撑作用被切断，结构受力己不再是单一轴向受力，而产生了部分弯曲受力的复杂受力状况。

The stress calculation method and strength condition of PET aerated water bottle were obtained from theory. The strength of PET aerated water bottle was simulated and calculated ANSYS. The stress graphics of the bottle with different thickness was plotted and their stress property was analyzed. The influence of axial load and grooves on bottle stress was also studied.

从理论上得到了聚酯碳酸饮料包装瓶的应力计算方法和强度条件；利用ANSYS对其强度进行了有限元模拟和计算，得到了不同厚度的聚酯碳酸饮料包装瓶的应力图，并分析了其应力特点；同时研究了轴向载荷和瓶体开凹槽对瓶体应力的影响。

The stress calculation method and strength condition of PET aerated water bottle were obtained from theory. The strength of PFT aerated water bottle was simulated and calculated ANSYS. The stress graphics of the bottle with different thickness was plotted and their stress property was analyzed. The influence of axial load and grooves on bottle stress was also studied.

从理论上得到了聚酯碳酸饮料包装瓶的应力计算方法和强度条件；利用ANSYS对其强度进行了有限元模拟和计算，得到了不同厚度的聚酯碳酸饮料包装瓶的应力图，并分析了其应力特点；同时研究了轴向载荷和瓶，婚开凹槽对瓶体应力的影响。

The air damping, quadrature error, parasite Coriolis force and interference from axial accelerations are also discussed.

讨论了微机械陀螺中的空气阻尼、正交误差、寄生Coriolis力以及轴向加速度干扰等问题。

A new type AMB-AB was brought forward in this paper, the film air bearing was integration in AMB. The axis space is saved and the rotors dynamics performance is improved.

本文研究了一种新型的磁气混合轴承结构，其特点是将箔片气体轴承集成在磁轴承的气隙里面，不占据轴向空间，因此与国外的研究有本质的区别。

An iterative temperature field model of cylinder, in which the non-linear steam temperature distributed along axial direction, was got based on two-dimensional transient heat conduction differential equation. Analytical simulation demonstrates not only a rapid solution convergence but a minor error.

在二维圆筒壁非稳态导热的基础上，得到了圆筒壁内蒸汽沿轴向线性分布，随时间非线性变化的温度场迭代计算公式，并与有限元计算结果作了对比，结果表明所得模型计算精度高、计算速度快。

This one mode pays close attention to network credence foundation of the businessman very much.

这一模式非常关注商人的网络信用基础。

Cell morphology of bacterial ghost of Pasteurella multocida was observed by scanning electron microscopy and inactivation ratio was estimated by CFU analysi.

扫描电镜观察多杀性巴氏杆菌细菌幽灵和菌落形成单位评价遗传灭活率。