轴向

The process of denting and the lateral load has been studied under different end conditions and axial pressure of different levels.

研究了在不同边界条件和初始轴向压力水平下，圆管构件的凹坑损伤形成过程和侧向承载力。

Computing method of tensioning elongation with the effects of lateral constrains and axial deformations is studied.

本文首次提出了超静定结构中考虑侧向约束和轴向变形影响的张拉伸长值的计算公式。

This paper introduces an analytic method of quick north seeker , whose principle is to use gyro to sense the component value of the angle-rate of the earth rotation, with which the northern azimuth angle between the referenced shaft of carrier and actual ...

本文提出一种基于解析的快速寻北方法，其原理是利用陀螺仪敏感地球的自传角速率分量，并由此计算出载体的参考轴向与真北方向的夹角，即偏北角。

This paper introduces an analytic method of quick north seeker , whose principle is to use gyro to sense the component value of the angle-rate of the earth rotation, with which the northern azimuth angle between the referenced shaft of carrier and actual north angle can be measured.

本文提出一种基于解析的快速寻北方法，其原理是利用陀螺仪敏感地球的自传角速率分量，并由此计算出载体的参考轴向与真北方向的夹角，即偏北角。

Results A series of data were gained of geometrical morphology and relative area of smooth muscle cells,elastin and collagen in axial and circumferential directions of the ascending aorta and aortic arch.

结果 获得了人升主动脉-主动脉弓几何形态和显微结构成分含量沿轴向和周向连续变化的完整数据。

The pattern of the tyre of agricultural vehicles has to fit in with the inclement working situations of the vehicles,which brings some difficulty to the pattern block mold design of the tyre.

文章介绍了农用轮胎的特点和轮胎模具的生产流程，然后结合轮胎花纹块的铸造、抛光、机械加工等工艺要求，阐述了农用轮胎花纹块模具设计方法并导出计算公式，内容包括：径向断面的工艺尺寸设计、轴向与周向的展开与弯曲设计；提出采用Coons曲面构造出模具内腔壁曲面的方法。

Low pulse before sift network operating principles : the use of double - sieve drum aircraft design; Work, pulp before sift upper tangent pressure the network into; Pulp the filter into the upper body of the dle two filter drum, double tilt-rotor rotary rotors, while the centrifugal force and centripetal forces role, through good mix inside and outside pool in sieve sieve drum body low extremity good mix of outflow; pulse in the tilt-rotor rotary drum filter

低脉冲网前筛工作原理：该机采用双筛鼓设计；工作时，浆料从网前筛上部切线压力送入；浆料从筛体上部流入到两个筛鼓中间，在双旋翼转子旋转时产生的离心力和向心力的同时作用下，良浆通过内、外筛鼓汇集于筛体下端的良浆管流出；脉冲旋翼在旋转时筛鼓不会赌赛，浆渣受转子旋转产生的轴向推动力，向下流送的同时被浓缩并逐步移到排渣口。

Low pulse before sift network operating principles : the use of double - sieve drum aircraft design; Work, pulp before sift upper tangent pressure from the network into; Pulp from the filter into the upper body of the middle two filter drum, double tilt-rotor rotary rotors, while the centrifugal force and centripetal forces role, through good mix inside and outside pool in sieve sieve drum body low extremity good mix of outflow; pulse in the tilt-rotor rotary drum filter

低脉冲网前筛工作原理：该机采用双筛鼓设计；工作时，浆料从网前筛上部切线压力送入；浆料从筛体上部流入到两个筛鼓中间，在双旋翼转子旋转时产生的离心力和向心力的同时作用下，良浆通过内、外筛鼓汇集于筛体下端的良浆管流出；脉冲旋翼在旋转时筛鼓不会赌赛，浆渣受转子旋转产生的轴向推动力，向下流送的同时被浓缩并逐步移到排渣口。

At this point, if the sizes of solid particles with the liquid into balance disc constantly in front of the high-pressure area, particle size less than or equal to A as the solid particles will flow through the axial gap.

此时，若大小不一的固体颗粒随着液体不断涌向平衡盘前面的高压区，粒径小于或等于A的固体颗粒会随着液流通过轴向间隙。

Ink, you can increase the color depth of a way to reduce Ink viscosity, improved printing ink and scraping knife wettability, so in axial and circumferential transfer content to reductionin.

油不朱方背，可以拔取挑矮色浓度贬矮油不朱黏度的方法，保守印版上的油不朱与刮不朱刀的湿润性，这样在轴向和周向油不朱迁徙度不对异不离放大了。

This one mode pays close attention to network credence foundation of the businessman very much.

这一模式非常关注商人的网络信用基础。

Cell morphology of bacterial ghost of Pasteurella multocida was observed by scanning electron microscopy and inactivation ratio was estimated by CFU analysi.

扫描电镜观察多杀性巴氏杆菌细菌幽灵和菌落形成单位评价遗传灭活率。