轴向

In the process of modeling, thermotical character and mechanical character of centrifugal compressor are emphased.

在建模过程中，重点对离心式压缩机的热力特性和机械特性做了较深入的研究，其中热力特性着重于离心式压缩机中的气流在各个关键截面参数和特性曲线，机械特性着重于压缩机转子轴系的振动和轴向力。

The results of XRD,TEM and Mossbauer effect show that underpressure,the orientation of acicular particles were redistri-buted,that is,the long axis tend to perpendicular to the direc-tion of the pressure.

X-ray衍射、穆斯堡尔谱和TEM的研究表明，在压力的作用下，针形颗粒产生了取向的重新分布，即长轴方向倾向垂直于压砧轴向。

It is shown that the ADFVLN, which has lower losses, high off-design performance and reliability, is superior to the vaned nozzle as the first stage and it also has more advantages than the early AFVLN, such as lower losses and less skewed boundary layer near the inner ring ect..

研究表明，这一新型轴流无叶喷嘴不仅具有原来同类喷嘴的优良性能，而且双出口结构和内环旋转的特点，使其流动效率明显提高，并省去两块隔板，缩短了机组的轴向尺寸，具有较高的工业应用价值。

Axial-Flow Fans. This type of fan is designed to cause air to flow parallel to the fan axis.

轴流风机：这种类型的风机设计使空气平行于风机的轴向流动。

Pipe heat causes linesr expansion and rurtherresult in tensile stress in the direction of pipe xale to make cracks in direction perpendicular to the axle,in the case ,the stress value is obtained by ormula=E,and if ,it is estimated with 15mm LG PEX-A Pipe as base,the sectional breaking rorce is estimated approx.7.6kg/cm2,being much more little comparing with the concrete bearing force=1,536kg/cm2and its not needed to be anxious to concrete cracking rising.

由于管子的线性热膨而使管子受轴向伸长力，从人在与管轴成直角的方向上产生裂缝，这时的应力接计算，PEX－A按直径15mm标准计算进断面破坏强度约为7.6kg/cm2，比混凝土的支持力1.58kg/cm2小得多，所以不需要考虑管子对混凝土的破坏作用。

I design two axis which taper is 1:12 to install bearing and fix bearing of cylindrical roller, I used locking nut to fix the direction of bearing owing to the reason of boring head's high precision.

主轴中设计了两个锥度为1：12的的轴段用于安装支承和固定圆柱滚子轴承，由于镗削头的精度要求很高，在轴承处使用了锁紧螺母进行轴向固定。

Check if the above still does not resolve, you can check the pump apart to see whether the broken shaft, but also check the pump ring, stationary ring is intact, the possibility of a small amount of rotor axial movement.

通过以上检查若仍不能解决，可将泵拆开检查，看泵轴是否折断，还应检查泵的动环、静环是否完好，整个转子可否少量轴向移动。

Test result makes clear, install rate matching steel to be the core profiled bar of 2.88%, the axial pressing intensity of test specimen can rise about 30%, axial is out of shape ability can raise about 1 times.

试验结果表明，设置配钢率为2.88%的核心型钢，试件的轴压强度可提高约30%，轴向变形能力可提高约1倍。

Additionally, cross section curve of helix wire, contact radius, clearance angle, width and ratio in wires same layer were obtained.

为了掌握轴向载荷下螺旋钢丝的变形特性以合理设计钢丝绳，推导了螺旋钢丝轴应变显式表达式，给出了螺旋钢丝截面曲线表达式和同层螺旋钢丝正好满足接触时钢丝的半径及接触半径、间隙角、间隙值和间隙率表达式。

In order to design reliable wire ropes by investigating the deformation characteristics of wires helix, axial strain's explicit expressions and radius' expressions of wires helix were deduced in which wires were bearing axial load and just touching each other. Additionally, cross section curve of helix wire, contact radius, clearance angle, width and ratio in wires' same layer were obtained.

为了掌握轴向载荷下螺旋钢丝的变形特性以合理设计钢丝绳，推导了螺旋钢丝轴应变显式表达式，给出了螺旋钢丝截面曲线表达式和同层螺旋钢丝正好满足接触时钢丝的半径及接触半径、间隙角、间隙值和间隙率表达式。

This one mode pays close attention to network credence foundation of the businessman very much.

这一模式非常关注商人的网络信用基础。

Cell morphology of bacterial ghost of Pasteurella multocida was observed by scanning electron microscopy and inactivation ratio was estimated by CFU analysi.

扫描电镜观察多杀性巴氏杆菌细菌幽灵和菌落形成单位评价遗传灭活率。