轴向

In this thesis, the Finite Element Method is applied to the solution of the Laplace equation formulated by means of stream function for the calculation of the static hydraulic thrust.

本文通过有限元法求解用流函数表示的拉普拉斯方程，进而计算轴流式机组的静态轴向水推力。

The torsional vibration, longitudinal vibration and ben- ding vibration of slender shaft in lathing because of axial feeding are calculated and analyzed.

对长细轴车削过程中，刀具轴向进给所产生的扭转振动、纵向振动、弯曲振动进行了计算与分析。

The result of the limit element analysis validates the analysis of the mechanics about the double punch.

从本次试验结果来看，径向压裂和轴向压裂法的试验值比较接近，结果低于单轴拉伸试验，土梁弯曲法的

Using two symmetrical plano-convex lens system to fabricate grating was analyzed and the characteristic of diffraction wavefront aberration of the grating was summarized by ray tracing program using MATLAB siftware.

分析使用两个对称的单平凸透镜光路制作光栅并用MATLAB编写光线追迹程序分析了所制作的光栅的衍射波像差的特点，经计算得出在较小焦比D/F情况下其衍射波像差仅与两支光路点光源的调节偏差之差有关与单独的各个偏差无关；初级像差中球差很小几乎可忽略：彗差仅与垂轴调节偏差之差成线性关系；像散仅与轴向调节偏差之差成正比；且当平凸透镜的焦比D/F增大时，各像差项迅速增大。

Axial elongation of inner isodiametric cells of the globular somatic embryo followed by the change in the growth axis of the procambium was an important event in heart-shaped or oblong-stage somatic embryo.

球形胚内部等径细胞轴向延长，接着前形成层生长轴发生变化，这些是心形胚或椭圆形体胚中的重要事件。

Based on this result, neutral axle and curvature radius of different section is developed.

应力理论由轴向力的平衡得出积分，在此基础上推导出曲杆不同的截面的中性轴，曲率半径。

In this paper,according to segregator and rotor of electric submersible pump,the limit axial force of the rotor with sliding bearing is calculated by FEM.

根据井下采油潜油电泵分离器轴及转子的总成结构，利用ANSYS有限元软件计算具有滑动轴承的转子系统稳定运转的极限轴向力。

Impeller with static balance is fixed onto the shaft by the sleeve and the sleeve nuts on the two sides. Its axial position may be adjusted through sleeve nut.

经过静平衡校验的叶轮，用轴套和两边的轴套螺母固定在轴上，其轴向位置可通过轴套螺母进行调整。

For SOV energized to counterclockwise drive shaft rotation, reconnect the actuated part to the other end of the drive shaft.

当电磁阀励磁，需要使输出轴向左回转时，只要把输出轴的另一端与被驱动体连接即可。

Continuous beam models with spring supports were set up to model end-plate connections. By comparing the results from tests with those from model analysis, the following conclusions can be drawn: during loading process, the neutral axis moves from the centroid axis to compression zone, not exceeding the center line of bolts inside the compression flange; ultimately, the tension flange and end-plate can be simplified as T-stub on the assumption that the axial forces of bolts in tension zone are equal to each other.

理论计算系建立带弹性支座的连续梁模型模拟端板连接，将模型计算结果与试验结果比较分析，结果表明：加载过程中，螺栓群中和轴逐渐从其形心轴向受压区移动，但不超过受压翼缘内侧螺栓中心线；极限状态下，受拉翼缘和端板可简化为等效T型件。

This one mode pays close attention to network credence foundation of the businessman very much.

这一模式非常关注商人的网络信用基础。

Cell morphology of bacterial ghost of Pasteurella multocida was observed by scanning electron microscopy and inactivation ratio was estimated by CFU analysi.

扫描电镜观察多杀性巴氏杆菌细菌幽灵和菌落形成单位评价遗传灭活率。