轴向

As a first step to industrialize this focusing coal liquefaction technology, it is essential to study the multiphase transport characteristics of this new type reactor. In this paper, mass transfer and mixing characteristics of a three-phase continuous loop reactor with a concentric draft tube were measured by the dynamic dissolved oxygen and saturated KCl solution pulse trace methods,with glass beads as solid phase, air as gas phase and tap water as liquid phase, respectively.

本文在同心内置Φ 0.14×1.5m导流筒的Φ 0.2×2.5m有机玻璃环流反应器中，以空气和水为气、液相，玻璃珠为固相，分别利用动态溶氧法与饱和KCl脉冲示踪法测量了液相体积传质系数和轴向分散系数，考察了表观气速、进料浆速、固含率、固相颗粒直径、液相表面张力以及操作方式对上述两个传递参数的影响规律，并将实验结果关联为量纲为1关联式；同时，根据环流反应器的结构特点，建立了传质系数分区模型和轴向分散系数分区模型且分别获得了解析解，对床层传质和混合的不均匀性做了理论分析。

In this thesis, a polarized femtosecond pump-probe spectroscopy system, combined with the technique to grow well-oriented high quality (100) and (001) Y1-xCaxBa2Cu3O7-δ thin films, has been developed to study the anisotropic ultrafast dynamics.

在本论文当中，利用自行发展的极化飞秒激发探测光谱系统；配合实验室具有，成长轴向解析之高品质(100)与(001)Y1-xCaxBa2Cu3O7-δ薄膜技术之能力，使我们可以量测在不同温度下，沿著各个轴向的薄膜瞬时反射率的变化。

These will provide theoretical guides for the design and the exploit of new products; By means of tensile testing of large number of the bi-axial warp-knitted fabrics, this paper delineated the inherent law of tensile properties especially in the relationships between the ground structures, materials and the fabric tensile properties; This paper also explained the problems existing in the domestic testing standard and measurement method of the warp-knitted grid products.

这个理论模型将为经编双轴向立体骨架织物的性能设计及生产提供很好的理论保证；本文通过对大量经编双轴向立体骨架织物拉伸性能的测试，了解掌握了该类织物拉伸性能的内在规律，为该类织物的性能设计打下了坚实的基础。

The first bearing has dual rows of ceramic ball bearings mounted to share all axial thrust loads on the shaft.

第一轴承为双排陶瓷球轴承，它们分担作用在轴向的所有轴向推力负荷。

Because of special geometry structure of three-cone bit, the top of formation will form a tri-spine well bottom while drilling with three-cone bit the drill string. It is the tri-spine well bottom that leads to the axial harmonic of vibration when the bit revolves a round and the three concavo-convex heave of bit and formation result in one time (1×rpm),two time (2×rpm), three time (3×rpm) turning table speed.

高岩由于三牙轮钻头的特殊几何结构，钻进过程中在岩层顶部容易形成一个三脊状井底，正是这一三脊状井底，当钻头旋转一周时钻柱轴向三次凸凹变化，由此在轴向产生1倍、2倍和3倍及其更高次倍于转盘转速rpm的谐波振动。

Because of special geometry structure of three-cone bit, the top of formation will form a tri-spine well bottom while drilling with three-cone bit the drill string. It is the tri-spine well bottom that leads to the axial harmonic of vibration when the bit revolves a round and the three concavo-convex heave of bit and formation result in one time (1×rpm),two time (2×rpm), three time (3×rpm) turning table speed.

高岩摘要：由于三牙轮钻头的特殊几何结构，钻进过程中在岩层顶部容易形成一个三脊状井底，正是这一三脊状井底，当钻头旋转一周时钻柱轴向三次凸凹变化，由此在轴向产生1倍、2倍和3倍及其更高次倍于转盘转速rpm的谐波振动。

Based on theory and test, finally, the measurements which may reduce axial force are given, for example, strengthening the management of size and clearances in roll systems and maintenance of roll bearings, limiting rolling technological conditions, increasing the axial flexibility, releasing axial binding forces and establishing axial flexible lock mechanisms, etc.. So it provides the constructive suggestions for preventing from damage of roll bearings.

在理论分析和实验验证的基础上，分析了轧辊轴承的受力特点和破坏原因，提出了降低轴向力的对策，其中包括加强尺寸及间隙管理、限定工艺条件、加强轴承的维修与管理等&硬&性措施，以及增加辊系轴向柔度、施放约束、建立柔性锁紧机构等&软&性措施，为现场解决轴承损坏问题提供了建设性参考意见。

Single-row Angular Contact ball bearings can sustain radial, axial or composite loads, however, any axial load must be in one direction.

单列角接触球轴承可承受径向，轴向或复合负荷，不过，任何轴向负载必须在一个方向。

Installation of two outer openings each staggered 180b, the inner and outer openings staggered opening 90b, and pin the three rings with a fixed, outer and inner expansion force in self-expansion force of working together, close to the surface of the pump cylinder run, inflation is not only the axial ring sealed, and the radial seal Ye Hao, it prevents micro-fine sand and into the axial friction pair, can also prevent the micro-fine sand and into the internal voids in the inner ring 3, the operation will not impede expansion ring breathing.

安装时2个外环开口互错开180b，内环开口与外环开口错开90b，并用销钉将3个环固定，外环在自身胀力和内环胀力共同作用下，紧贴泵筒内表面运行，胀圈不但轴向密封好，而且径向密封也好，故阻止微细砂进入轴向摩擦副，也可阻止微细砂进入内环3的内部空隙中，不会阻碍胀圈运行中呼吸。

The performance curves of the experimental fan have been obtained and the flow field has been measured at the best efficiency point of each setting angle, in fixed plane downstream the rotor with a constant temperature hot-wire anemometer and a periodic multisampling and averaging technique by an on-line microcomputer.

对轴流式通风机在不同安装角时的流场变化进行了实验研究，得到了通风机的总性能曲线；并用固定在转子前、后测量平面的热线，测量了最高效率点处不同安装角时叶片通道进、出口轴向和切向速度的分布，从而能够清楚地了解到，通风机在安装角变化时，叶片通道进、出口截面流动结构的变化。

This one mode pays close attention to network credence foundation of the businessman very much.

这一模式非常关注商人的网络信用基础。

Cell morphology of bacterial ghost of Pasteurella multocida was observed by scanning electron microscopy and inactivation ratio was estimated by CFU analysi.

扫描电镜观察多杀性巴氏杆菌细菌幽灵和菌落形成单位评价遗传灭活率。