轴向

Axial piston pump Body Pump is ZB40 one of the key components.

轴向柱塞泵泵体是ZB40柱塞泵的关键零件之一。

In order to find out the reasons of the plunger pump damage,the destroyed situation of the axial-plunger pump in the hydraulic shearing machine.

通过分析液压剪轴向柱塞泵的破损情况，找出了柱塞泵损坏的原因。

A study in form and geometry, the plaza continues the form language of the axial connection and extrudes it into the third dimension through the addition of precast concrete seat walls set in plinths of decomposed granite and surrounded by mixed understory plantings.

研究的形式和几何，继续在广场的形式语言和挤出轴向连接到第三个层面通过增加预制混凝土墙壁座位设置在plinths的风化花岗岩，四周是混合林下种植。两个大的白色长廊充当铺路的主要东西流通整个网站。

It is proved that expansion of migrating pingo can produce axis stress of 11 to-21 MPa,formed concentrat...

结果表明，移动冰丘能够产生11~-21MPa的轴向应力和15~-31 MPa的主应力，在桥墩周围形成不同规模的应力集中区，导致桥墩发生显著偏移。

It is proved that expansion of migrating pingo can produce axis stress of 11 to -21MPa, formed concentration of stresses and caused evident displacement and deviation of bridge pier.

结果表明，移动冰丘能够产生11~-21MPa的轴向应力和15~-31MPa的主应力，在桥墩周围形成不同规模的应力集中区，导致桥墩发生显著偏移。

It features compact in design,light in weight,high precision and small fitting clearance.

单排交叉滚柱式回转支承，由两个座圈组成，结构紧凑、重量轻、制造精度高，装配间隙小，对安装精度要求高，滚柱为1：1交叉排列，能同时承受轴向力，倾翻力矩和较大的径向力，被广泛地用于起重运输、工程机械和军工产品上。

With ASFC technology, it shall be possible to increase efficiently fan/compressor pressure ratio, but also reduce the axial length and weight of the engine a well as the noise of fans. Meanwhile, it increases the flexibility sad payload of the flight vehicle, thus reducing the fuel consumption.

这一技术的采用能够大幅度提高压比，减少发动机的轴向长度和重量，降低风扇的噪音；在做功能力增加重量减轻的同时，能够增加飞行器的灵活性以及有效载荷，从而减少燃油消耗。

And the supplementing material function of axial feeding mainly happened at stage of low pressure forming.

且轴向进给的补料作用主要发生在低压成形阶段。

The distributions of the axial pressure in the tube under different injection parameters were measured. The experimental data of the different structure of the slots were also analyzed.

测量了不同射流参数下管内的轴向压力分布，并且对不同结构的射流槽的试验结果进行了比较。

The typical shape of the stress-strain diagram for structural steel is shown in Fig.1, where the axial strains are plotted on the horizontal axis and the corresponding stresses are given by the ordinates to the curve OABCDE .

图1 显示的是结构钢材的应力-应变关系图的典型形状；轴向应变是沿着水平轴线绘制，而相应的应力是以坐标至曲线0ABCDE体现。

This one mode pays close attention to network credence foundation of the businessman very much.

这一模式非常关注商人的网络信用基础。

Cell morphology of bacterial ghost of Pasteurella multocida was observed by scanning electron microscopy and inactivation ratio was estimated by CFU analysi.

扫描电镜观察多杀性巴氏杆菌细菌幽灵和菌落形成单位评价遗传灭活率。