轴切的

According to spatial analytic geometry,the mathematical model of intersecting of pipe and cone was established.

利用空间解析几何的原理建立了管锥相贯数学模型，用参量方程描述了管端相贯线焊接坡口的几何形状，该数学模型可应用于三轴联动火焰数控切管机。

In general, the deformation of the model grille is a combination of axial and shear strains

一般情况下，模型栅格的变形是轴向应变和切向应变的组合。

The three-orientaion inclined hot-wire technique can be used to measure three dimensional velocities accurately.

研究表明，用五孔球探针可以测定旋风分离器的切向与轴向平均速度，但径向平均速度的测量精度不高。

On the hanging wall of the nappe,isoclinal folds are developed with the axial planes inclined to the north in association with imbricated thrusts dipping to the south. In the foot wall,there exist rather wide ductile shear zones. Also,a set of structural windows and klippen are distributed along the zone . The distance of the dislpacement is estimated at about more than 20km.

推覆构造上盘变质岩中同斜倒转褶皱发育，轴面向北倾倒，伴有一组向南倾斜的叠瓦式冲断面；下盘见有较宽的韧性剪切带；还发现有一系列飞来峰与构造窗沿推覆构造带分布，推测推覆距离在20km以上。

Planet reduction shown in figure 6. Loose nut 6 "nut + washer + anti-loose nut". The explored view is Adjust torque 350~400N.m, rotate hub 13 at the same time. 5 and a radial force F=70N crease, hub can rotate free. Then fix lock washer into nut 6, fasten loose nut with torque 400N.m and make spacer control 0.05~0.15mm.

调整时，用 350~400N.m 力矩旋紧螺母 6，同时转动轮毂 13，使两轴承处于正确位置，然后，稍旋松螺母 6，在轮辋螺栓处施加一个切向力 F=55N.m，此时轮毂应能自由转动，然后装上止动垫片 5，将其卡爪折入螺母 6 的防转槽内，再用 400N.m 的力矩旋紧防松螺母，使轴向间隙控制在 0.05～0.15mm 之间。

The apparatus for static and dynamic universal triaxial and torsional shear soil testing is employed to perform stress-controlled cyclic coupled vertical and torsional shear test by different cyclic stress paths. Through a series of tests on saturated clay, the dynamic deformation, stress-strain relationship and dynamic strength are systematically investigated under rotation of principal stress axes.

针对饱和黏土，利用土工静力－动力液压三轴－扭转多功能扭剪仪进行了均等固结下的耦合循环剪切试验，着重研究了不同循环应力路径对应力－应变关系和强度特性的影响。

Based on the existing 3-D mechanical equation of drill string, considering the influence of lateral shearing strength and shearing strain on flexural deflection of drill string, the universal basic equations for the shearing deformation of drill string are established according to the deformation and force characteristics of the drill string.

该公式综合描述了横向剪切变形和轴向钻压对钻柱横向振动固有频率的影响，是对现有钻柱力学基础理论的补充和完

The mechanical properties and the influence of water are study by means of large scale compression test and triaxial test.

通过巨粒土室内大型压缩试验与三轴剪切试验，研究了巨粒土的力学特性以及水的影响。

The analytical expression of axie displacement, axie stress and interlaminar shear stress were given under some simple loading forms.

给出了一些简单载荷作用下的轴向位移、应力及层间剪切应力的解析表达式。

In operation, a annular cutting knife moves forward to cut off the knife anvil (4),and when the annular cutting knife moves backward, it carries off the inner ring of the knife anvil (4), the elastic locking piece (5) is springed back and replaced.

手术时，环形切刀向前运动切断刀砧、后退时把刀砧内圈带走，弹性锁片发生回弹复位，在各种辅助机构的配合下，钉砧环便可以绕着钉砧轴发生翻转。

On the other hand, the more important thing is because the urban housing is a kind of heterogeneity products.

另一方面，更重要的是由于城市住房是一种异质性产品。

Climate histogram is the fall that collects place measure calm value, cent serves as cross axle for a few equal interval, the area that the frequency that the value appears according to place is accumulated and becomes will be determined inside each interval, discharge the graph that rise with post, also be called histogram.

气候直方图是将所收集的降水量测定值，分为几个相等的区间作为横轴，并将各区间内所测定值依所出现的次数累积而成的面积，用柱子排起来的图形，也叫做柱状图。