轴切的

Then the hazard zone of tire/rim contact area with axial force of cord,Mises stress,shearing strain and strain energy potential were analyzed.

同时运用帘线轴力、M ises应力、剪切应变、应变比能4个力学量对胎圈部的危险区域进行了精细分析。

Under maximal flux (Vi = 4.3 m/s),fluid field of 16 cross sections in the model were investigated, the tangential velocity empirical equation of each partition was got, and empirical equations of axial and radial velocity on the ring partition between baffle bar and cylinder wall were obtained.

在全气速（Vi = 4.3 m/s）下测得了流场中各部分共计16个截面的流场分布，分别拟合得到各区域外旋流中切向速度分布经验公式；拟合得到在导流体与筒壁间环形段轴向速度分布和径向速度分布经验公式。

Rotational movement of the shaft is transmitted to the blade subassemblies through viscoelastic material which is torsionally loaded and stressed in shear.

旋转运动的轴转交给刀片组件，通过粘弹性材料是扭矩加载，并强调在剪切。

The theoretical predictions are compared with triaxial drained and undrained compression test results of a marine soft soil; it is shown that the model is reasonable.

将理论预测与某海洋软土三轴排水与不排水剪切试验结果比较，显示了该模型的合理性。

The results clearly prove an evolution mechanism of type B PLC shear bands, that is, a PLC shear band first nucleates at one side of specimen, then transversely runs through the entire specimen section with a certain angle, finally forms an inhomogeneous deformation bands.

实验结果清楚地证实了B型PLC剪切带的一种演化机制，即先在试样一侧成核，然后与拉伸轴成一定角度横向贯穿整个试样，最终形成非均匀塑性变形带。

The ore body was contolled by both the co axial overprinted fold of two periods and the ductil brittle shear fault.

矿体的赋存状态主要受两期共轴迭加褶皱构造和韧脆性剪切断裂复合控制。

Top sintering material preheats for a short time、sinter at lower temperature、cools too fast and has low crystallinity, especially, network SFCA offorms difficultly in the top layer, that results in high ratio of pore, so the strength of top sinter is low. when thickness of sintering material is increased, the ratio of top sinter will be decreased, in its entirety, the strength of sinter will rise.

5烧结矿破碎属脆性断裂，一般在单轴压缩应力下受剪切产生，本文基于低氟烧结矿物质组成，导出了基体抗压强度与烧结矿物质组成的关系式，由此得出，基体抗压强度受磁铁矿影响不大，而受铁酸钙影响较为显著。

Introduces a new technology for hobbing small module and fewer teethed gear with the usage of the transmission chain of Y631K spline shaft milling machine by adding the number of index change gears.

介绍利用Y631K 花键轴铣床传动链，适当增加分度挂轮数，滚切小模数、少齿数齿轮轴的加工技术。

Epicotyls were cutted longitudinally and cultured in the dark first,on the MS basal medium with 3 mg/L 6-BA and 30 g/L sugar,100% adventitious shoot induction and an average of 33.8 shoots per explant were obtained.

上胚轴纵切结合前期暗培养，在MS附加6-BA 3mg/L、蔗糖30g/L 培养基中，不定芽诱导率为100%，每个外植体平均诱导的不定芽数达33.8

All the species are characterized by having an adaxial epidermis of the ligules consisting of oblong, tabular cells, with the radical and tangential walls being straight; the outer wall with a characteristic thickening along the median plane of the cell; the median plane of the cuticle of outer wall with a pattern of longitudinal rugose stripes; and no systematic connection between the patterns of adjacent cells.

所有种类舌片近轴面的细胞为板状，长圆形；径向、切向壁直；外壁特征性突起，外壁中央为纵向皱纹，相邻细胞之间的纹饰无系统连接。

On the other hand, the more important thing is because the urban housing is a kind of heterogeneity products.

另一方面，更重要的是由于城市住房是一种异质性产品。

Climate histogram is the fall that collects place measure calm value, cent serves as cross axle for a few equal interval, the area that the frequency that the value appears according to place is accumulated and becomes will be determined inside each interval, discharge the graph that rise with post, also be called histogram.

气候直方图是将所收集的降水量测定值，分为几个相等的区间作为横轴，并将各区间内所测定值依所出现的次数累积而成的面积，用柱子排起来的图形，也叫做柱状图。