轴切的

Contributions of the centripetal acceleration in steady flight, the tangential acceleration due to the effect of the angular acceleration, the Coriolis component of acceleration, the radial (the vertical direction at prototype), circumferential and axial (the two horizontal directions at prototype) shaking effects and the elongation effect of the centrifuge arm to the global acceleration of a particle in centrifuge modelling are identified in the expression of the global acceleration.

笔者描述了整体加速度表达式中各项的物理意义，指出了离心机稳定运转时的向心加速度、由角加速度效应引起的切向加速度、互补加速度分量、径向、环向和轴向振动效应以及离心机臂伸长效应对整体加速度的贡献。

This paper researched the key part of framework aclinic slide structure on diamond frame sawing machine, which is the axially moving hydrostatic journal bearing. The major sawing motion form of diamond frame sawing was analysed. The structure designing model of the bearing according to the practice was established; and by the systemic analysis and research on the lubricating mechanism and performance, the designed scheme was proved out.

本文通过对金刚石框架锯主要锯切运动形式分析，以金刚石框架锯锯框水平滑动机构关键件－轴向运动液体静压轴承为研究对象，结合实际建立了该轴承的结构设计模型，通过润滑机理与性能的系统分析研究，实现了对设计方案的有效验证，并满足实用要求。

The lateral displacement of the frame structure coursed by the bending of beam and column is belonged to shearing type, the lateral displacement coursed by the axised deformation is belonged to bending type.

框架由于梁、柱弯曲变形所产生的侧移属于剪切型，而由柱的轴向变形所引起的侧移属于弯曲型。

Therefore, the face-width of the face gear is limited. According to the conditions of undercutting and pointing, the formulae of minimum inner diameter and maximum outer diameter are derived for the shaft angle face gear .

根据产生根切与齿顶变尖的条件，给出了任意轴交角下齿宽设计的公式，定义了两个无量纲参数，即最小内半径系数和最大外半径系数，来表示齿宽的设计范围。

The main vibratory system of the screen consists of the balance substance and shear rubber spring while the vibration isolation system is composed of the balance substance and vibration isolation spring.

筛机由机体平衡质体与简切橡胶弹簧组成主振系统，机体平衡质体与隔振弹簧组成隔振系统，筛机的振动是由装于平衡质体中间的单轴惯性激振器激励的。

The compressive strength and elastic wave velocity of cement soil are determined respectively by consolidation non-drainage triaxial shear test and transmission method so as to study the effect of saturation on the compressive strength, the elastic wave velocity and their correlation.

用固结不排水三轴剪切试验方法和透射法，分别测定改良土的抗压强度和弹性波速，从而研究饱和对水泥改良土抗压强度、弹性波速的影响以及两者的相关性。

My company has the high-precision large and medium-sized CNC milling spiral bevel gear tooth 4-axis CNC machine tools used not only servo-driven, SIEMENS 802D control system to roll all of milling spiral bevel gear, zero Bevel Gear and quasi-double Surface gear, and to the world's most advanced coordinates Coaxial design, successfully applied in the processing of new products in diameter.

我公司拥有的高精度大、中型数控弧齿锥齿轮铣齿机床不仅采用数控四轴伺服驱动、SIEMENS 802D控制系统，以滚切法铣削弧齿锥齿轮、零度齿锥齿轮及准双曲面齿轮，且把当今世界最先进的坐标轴式设计，成功应用于大加工直径的新产品之中。

The results show that the tangential velocity distribution in the annular space shows a typical feature of strongly swirling flows and it consists of quasi-free vortex area and quasi-forced vortex area.

由于流体与双侧壁面之间的摩擦造成能量损失和湍流能量耗散，导致最大切向速度不断衰减且位置沿轴向向下逐渐向提升管外壁移动，同时涡量传递造成外部的准自由涡区逐渐增大，内部的准强制涡区逐渐缩小。

First, natural frequency of Euler-Bernoulli beam with elastic bearing and without the axial force is put forward. And numerical method is used to solve the equation by a program designed by the author, and the influences of shearing deformation and rotatory inertia on frequency are analyzed.

首先对不考虑轴力影响的弹性支座Euler-Bernoulli梁的固有频率进行了推导，并用自编程序进行了数值法求解，同时分析了剪切变形和转动惯量(Timoshenko梁)对频率的影响。

According to the simulation of the mixing property for KBME, the axial distributive mixing property and the shear property of reversed kneading blocks are better than those of neutral and forward ones, and those of normal screw element are worst, whereas the kneading disc width has few impacts on these two properties.

通过对捏合盘混炼段的混合性能模拟可知，就轴向分布混合性能和剪切性能而言，反向捏合块元件优于正向元件和中性捏合块元件，捏合盘厚度对这两个性能的影响不大，而常规螺纹元件的这两个性能相对较差。

On the other hand, the more important thing is because the urban housing is a kind of heterogeneity products.

另一方面，更重要的是由于城市住房是一种异质性产品。

Climate histogram is the fall that collects place measure calm value, cent serves as cross axle for a few equal interval, the area that the frequency that the value appears according to place is accumulated and becomes will be determined inside each interval, discharge the graph that rise with post, also be called histogram.

气候直方图是将所收集的降水量测定值，分为几个相等的区间作为横轴，并将各区间内所测定值依所出现的次数累积而成的面积，用柱子排起来的图形，也叫做柱状图。