轴

Based on rubbing model of a two-disk rotor-stator system with consideration of both rotor and stator dynamics,a numerical integration program is applied to numerical simulation and analysis of the nonlinear dynamics of this system,such as bifurcation,Poincare section map,trajectory of axes,phase trajectory,frequency spectrum diagram and time response.

基于一新型径向-轴向复合碰摩双盘转子-机匣力学模型，利用数值积分和Poincare映射方法，对转子-机匣系统由于径向-轴向碰摩故障导致的非线性动力学行为进行了数值仿真研究，给出了系统响应随转速和偏心量变化的分岔图和一些典型的Poincare截面图、相轨图、轴心轨迹、幅值谱图和时域响应等。

When an image digital holographic microscopy layout is employed, the Fresnel integral cannot be used in separating the reconstructed image from its conjugate image and background.

在像面数字全息中，用菲涅尔衍射积分进行复振幅再现的方法已不适用，将相移同轴技术与数字全息显微术结合，研究了以平行光为参考光记录相移同轴像面显微数字全息图及其幅度和相位再现方法。

It is the product combining friction drive and screw drive.

它是将主动轴与从动轴相交成一个非常小的角度。

Matlab ellipse paintings did not provide the function, which was oval in the center long axis of oval painting after the short axis, in which the use of complex variable function.

matlab没有提供画椭圆的函数，该函数在获得椭圆中心长轴短轴后进行画椭圆，其中使用复变函数。

In order to develop this local property,this paper presents a method,which uses Fourier Series to approximate the boundary shapes of the shafts with periodic boundary of cross section,and uses the conformal mapping in Theory of Function of a Complex Variable to make the complicated boundary shapes of the shafts map a unit circle.Thus elastic theory can analyze...

本文提出一种方法，其实质是：采用富里埃级数来逼近横截面呈周期性变化边界的轴类零件的边界形状；并应用复变函数论中保角映射原理，将零件复杂的边界形状映像成单位圆，从而使弹性理论可以分析和计算复杂边界轴类零件的应力场；再通过留数的求解实现保角映射的反变换。

And will provide the experience about the maintenance by using the self-made simple gantry crane and static balancer.

就L60立式轴流风机轮毂与输出轴难于拆卸的问题和叶轮静平衡测试问题进行探讨，并提供用自制的简易龙门架和静平衡装置的方法进行检修的经验。

One undercooling criterion of equi-nucleation is derived from analysis of Gaussian distribution model of heterogeneous nucleation.

通过对高斯异质形核公式的研究，给出了等轴晶开始形核的过冷度判据，更为准确的描述柱状晶向等轴晶的转变过程。

The propagation equations for oblique and off-axial Gaussian beams passing through cat-eye optical lens are deduced by using the theory of matrix optics and expanding the aperture function into a finite sum of complex Gaussian functions.

运用矩阵光学理论以及将硬边光阑窗口函数展开为有限个复高斯函数之和的方法，进一步推导了倾斜离轴高斯光束通过猫眼光学镜头的解析传输公式，通过数值计算分析得到了倾斜系数和离轴量对猫眼效应反射光光强分布的影响规律。

To this end, the gear-driven motor and pump should be connected by flexible couplings, and installed on the same floor, to ensure that the coaxial, the floor installed in elastic support, can further improve the effect of isolation.

为此，齿轮泵与驱动电机应通过柔性联轴器连接，并安装在同一底板上，以保证同轴度，该底板装于弹性支承上，可进一步提高隔振效果。

The driving consists of synchronous belt, gearwheel device and universal shafts with high driving efficiency and low consumption.

同步带、齿轮箱万向轴联轴器相结合传动型式，传动效率高，构件损耗低。

Breath, muscle contraction of the buttocks; arch body, as far as possible to hold his head, right leg straight towards the ceiling (peg-leg knee in order to avoid muscle tension).

呼气，收缩臀部肌肉；拱起身体，尽量抬起头来，右腿伸直朝向天花板（膝微屈，以避免肌肉紧张）。

The cost of moving grain food products was unchanged from May, but year over year are up 8%.

粮食产品的运输费用与5月份相比没有变化，但却比去年同期高8％。