轴

In a further preferred embodiment, the elongated support member is a parallelepiped with an axially extended slot, in which the optical fiber is secured with its longitudinal axis substantially parallel to the axially extended slot.

在进一步优选的实施例中，长形的支撑构件是一个具有轴向延长槽的平面平行六面体，其中光纤安装在与轴向延长槽充分平行的纵轴上。

According to the characteristic that the definition point of the Q matrix of wave front is always located on the extremum point on the axis of the beam, a three-dimensional formula for the rectificative factor of phase in complex ray paraxial approximation is proposed, which calculates the rectificative factor of phase directly without considering the calculation of the main directions and curvatures and the rotation of the coordinates, thus simplifying the paraxial approximation calculation by the complex ray expansion method.

根据波前Q矩阵的定义点总位于波束轴上极值点的特点，提出了三维复射线近轴近似相位校正因子计算公式。该公式不用考虑主方向和主曲率的计算和坐标旋转，直接计算相位校正因子，从而简化了复射线展开法的近轴近似计算。

Chapter 2: The vectorial properties of the paraxial beams propagating perpendicular to the optical axis of a uniaxially anisotropic crystal are investigated.

第二章：研究了垂直光轴入射的傍轴光束在单轴晶体中传输的矢量性质。

The flow field model of port plate pair in condition of the linear axial pressure distribution and dynamic model of flow divider pintle supporting system in abruptly variable load were established. Based on the two models, the balancing characteristics of flow divider pintle in ball piston pump was investigated.

在轴向压力线性分布的条件下，建立了配流副的流场模型，同时建立了配流轴支承系统在突变载荷下的动态仿真模型，在此基础上对球塞式液压泵配流轴的平衡特性进行了研究。

This paper analyzed the randomness of the relative position relation between the common vertical line of the two axes of a coupling and two centers of a coupling during installing machines,and the randomness of the position of the support plane on which a machine is installed.It pointed out the errors formed by the two randomness and illustrated the faults of the four parameters system which is used in describing the shaft alignment error of a coupling by abroad technician.

分析了机器安装过程中联轴器两轴线的公垂线与联轴器中心的相对位置关系的随机性及机器地脚支承面方位的随机性，指出了两种随机性所产生的误差，说明了国外工程界在描述联轴器对中误差时所用的4参数体系存在的不足。

By Visual Basic 6.0 program, taken the distance between hole 200mm and buried depth 120～150mm as the optimization goal, the most optimum parameters range of the mechanism was obtained as follows: the initial angle between planet frame and the line formed from spraying-fertilizer needle-tip and planet wheel axle was -45°～-40°, the initial angular displacement of planet frame was 40°～50°, the distance between spraying-fertilizer needle-tip and the planetary gear axle center was 280～300mm, simultaneously, the semi-major axis of elliptic gear was 29.364mm, the teeth quantity was 23, the ratio of semi-minor axes and semi-major axis was 0.958, the radius of circular gear was 25mm.

对该机构进行运动学分析，建立了数学模型，以穴距200mm和入土深度120～150mm为寻优目标，应用Visual Basic 6.0软件编程得出满足机构运动要求的最优参数范围为：喷肥针尖和行星轮轴连线与行星架的初始夹角-45°～-40°、行星架初始角位移40°～50°、喷肥针尖与行星轮轴心距离280～300mm，此时椭圆齿轮长半轴29.364mm、齿数23、短半轴与长半轴比0.958，正圆齿轮半径25mm。

Unfasten the Decl. clamp and turn the optical tube until it is nearly at right angles to the polar axis. If you do not do this, the polar axis scope will be shaded with the Decl. axis and can not be used.

松开赤纬制动钮并转动望远镜镜筒直到它与极轴镜的角度接近直角，如果你不如此做，极轴望远镜将被赤纬轴遮挡而无法使用。

Our patients were seen to have higher rate of feet postaxial polydactyly both clinically and radiologically; they had lower rate of clinical postaxial polydactyly over hands, with feet preaxial polydactyly both clinically and radiologically compared to previous review articles covering 52 cases.

临床上，与文献上收集52例比较不管是外观或放射线检查上皆有较高比例的足部中轴后多趾；较低比例的手部中轴后多指及足部中轴前多趾之现象。

The vibration equations with the coefficients related to and short-circuit currents, axial precompression, property of pressboard are formulated.

提出了绕组对称分布安匝平衡时的等效单自由度轴向振动模型，推导出了绕组轴向振动方程各参数与短路电流、轴向预紧力、绝缘垫块弹性等因素之间的定量表达式。

Aimed at the minimum maximum principal stress,based on three dimensional finite element analysis,with the help of FEM software,an optimization method is used to design the main parameters of the joint cross of universal coupling.

利用ANSYS软件对轧机主传动系统的万向联轴器十字轴进行三维有限元分析，在此基础上，以十字轴所承受的最大主应力最小作为追求目标，在ANSYS软件中对其主要参数进行了优化，得出了较为理想的结果。

Breath, muscle contraction of the buttocks; arch body, as far as possible to hold his head, right leg straight towards the ceiling (peg-leg knee in order to avoid muscle tension).

呼气，收缩臀部肌肉；拱起身体，尽量抬起头来，右腿伸直朝向天花板（膝微屈，以避免肌肉紧张）。

The cost of moving grain food products was unchanged from May, but year over year are up 8%.

粮食产品的运输费用与5月份相比没有变化，但却比去年同期高8％。