软化

Characteristic: Wax-like dark brown solid, intenerated under heat, at 30℃ turns into paste and becomes into viscous liquid at 40℃, soluble in vegetable oils and organic solvents like ethanol, hexane and acetone.

性质： 外观为深棕色蜡状固体，遇热软化，30℃为膏状，40℃以上为粘稠液体，溶于植物油和乙醇、己烷、丙酮等有机溶剂，不溶于水。

Hotmelts gradually build Crystal rrepublic Crystal builds, increased sensitivity to temperature of matozoa, will be thrown out of the hotmelts of intenerated again is threatened by high-temperature polymer-coated occurrence causes a close Crosslinking thermal features, so we use water cooling and instant automatic segmentation algorithm to prevent heat build-up to resin coated products out of the heat source immediately after the creation of an area of low-temperature curing quenching.

会使热熔胶逐渐生成晶体。晶体的生成，提高了胶体到温度的灵敏性、将可能引发出热熔胶的再次软化，削弱了高温覆膜操作使其近似发生交联反应的抗热功能，所以我们使用水冷及即时进行自动分割，防止热量积聚，为覆膜产品脱离热源后即时创造一个低温骤冷固化区。

Electronic laminating machine this behavior particularly acute exceeded the critical temperature to master film covering the work area, not only complex, as well as well so that the markinf matozoa near the cross-linking reaction, matozoa issued the curing approximate hard, so that when it again when heated intenerated reluctant, covered with plastic film operation the correct temperature control methods, and that is fine is extremely close to master the cross-linking reaction temperature of the resin coated temperature.

电子复膜机这种现象特别明显）恰到好处地掌握覆膜温度临界工作区域，不仅复合效果好，同时还使热熔胶体接近交联反应的热点，胶体的固化近似发硬、这样当其再度受热时就不会轻易软化，覆膜操作正确的温度控制方法，就是精细掌握这种极为接近交联反应温度的覆膜温度。

By adopting strain intenerated model and using numerical calculation of FLAC(Fast Lagrangian Analysis of Continue), deformation and destruction course under pick cutting is researched, different parameters' great influence on plasticity district, max displacement, max main stress and max shearing stress under the various kinds of operating modes is analyzed.

采用应变软化的模型，使用连续介质快速拉格朗日分析法(FLAC，FastLagrangianAnaly-sisofContinue)进行数值模拟计算；研究截齿截割作用下煤体变形破坏过程；分析各种工况下不同参数对煤体塑性区、最大位移、最大主应力、最大剪应力的影响。

He sintering of Ti/Al -Al_2O_3 powder in nm scale on SPS is composed of those moments: originally pressing period, exhausting and intenerated period, Al's consumption period,Al_2Ti's creation period, the main alloying and consolidation period and homogenization period.

i/Al-Al_2O_3系纳米级别的粉体在SPS上的烧结过程中，主要分为初始加压阶段、排气与软化阶段、Al消耗阶段、Al_2Ti生成阶段、主要合金反应与烧结阶段和均匀化阶段。

This paper introduces the developing progress of metallic pressure sealing ring,including selecting material,drawing special forging process, intenerating process and drawing machining process.

介绍了具有优良使用性能，可替代进口产品的金属自密封环的研制，包括选材、制定特殊锻造工艺、制定机械加工工艺规程和软化处理等。

Based on the proposed measures and procedures, in allusion to the current status of intenerating constraints on budget control of our country, this thesis makes further detailed analysis into the legislative requirement for public expenditure administration and points out that it must start with the actualization of legislative administration on public expenditure budget.

本文在提出有效途径和方法的基础上，针对我国预算约束软化的现状，进一步分析公共支出管理法制化的内在要求。

And in quantitative analysis, some methods including classical input-output analysis and gray-interaction method are discussed and considered that they themselves cannot make enough interpretation on the swelling effect The paper deeply probes into information industrial hierarchy which defines Information Industrial Intenerating Coefficient and Information Industrial Intelligence Dense Coefficient, divides three stages of information industrial evolution on the base of comparing these two coefficients with"1".

在定量分析中，作者对传统的投入产出法、灰色关联法等方法进行了讨论，认为它们都不能充分解释信息产业对传统产业的巨大影响。论文深入探讨了信息产业的层次结构，提出了信息产业软化系数和信息产业智密化系数，并根据这两个系数与&1&的比较将信息产业的演进按层次结构分为三个阶段。

Abstractsomemedia reported the solemn topic like anti-corruption, by the way of intenerating them. This deformed trend not only damaged the media's reverence, but also blurred the sight of people.

在当前娱乐化大潮的影响下，一些媒体为了追求所谓的&卖点&，把严肃的反腐败报道加以&软化&，即用娱乐化方式进行报道。

In order to meet the need of high speed continuous casting,the moulding powder demands lower viscosity,lower crystallization temperature,lower intenerating and melting temperature,high melting rate,optimum basicity and chemical composition.

高速连铸保护渣的物化性能不同于普通连铸，应具有低粘度、低结晶温度、低软化及熔融温度、较快的熔化速度以及合适的碱度和化学成分等特性，以满足高拉速的需要，减少生产事故，提高铸坯质量。

But we don't care about Battlegrounds.

但我们并不在乎沙场中的显露。

Ah! don't mention it, the butcher's shop is a horror.

啊！不用提了。提到肉，真是糟透了。