软化

The results show that the flow stress decreases with increasing deforming temperature and increases with increasing strain rate. The flow stress of the alloy during hot compression deformation can be described by constitutive equation in hyperbolic sine function with a hot deformation activation energy of 196.27 kJ/mol. Partial recystallization takes place in the alloys deformed at a high temperature or at a low strain rate, and large number of dislocations and subgrains are observed in the alloy. The elongated grains observed in the samples coarsen with increasing temperature and decreasing strain rate. Correspondingly, the subgrain size increases and the dislocation density decreases. The main soften mechanism of the alloy transforms from dynamic recovery to dynamic recrystallization.

结果表明：Al-Cu-Mg-Ag耐热铝合金在热压缩变形中的流变应力随着温度的升高而减小，随着应变速率的增大而增大；该合金的热压缩变形流变应力行为可用双曲正弦形式的本构方程来描述，其变形激活能为196.27kJ/mol；在变形温度较高或应变速率较低的合金中发生部分再结晶，并且在合金组织中存在大量的位错和亚晶；随着温度的升高和应变速率的降低，合金中拉长的晶粒发生粗化，亚晶尺寸增大，位错密度减小，合金的主要软化机制逐步由动态回复转变为动态再结晶。

Additionally, the effect of fluorine content on softening temperature and thermal expansion coefficient of glasses was investigated.

另外通过玻璃的热膨胀行为分析了氟对玻璃软化温度和热膨胀系数的影响。

Results indicate that when the strain rate is 1200 s-1, the twin number of samples in different orientation increases with plastic strain increasing; when the strain rate increases to 2800 s-1, the σ-ε curves have no obvious charges as the angle is 0o and 45o, compared with that at 1200 s-1; however the σ-ε curves vary from concave to convex when the angle is 90o, because thermal softening has occurred with increasing plastic strain, which results in the number of twin decreasing, and smaller strain hardening

结果表明：当加载应变率为1200 s-1时，不同取样方向的样品中孪晶数量均随塑性变形应变量的增大而增多；当加载应变率增大到为2800 s-1时，取样方向为0°和45°、流变曲线形状较应变率为1200 s-1时没有明显变化，而取样方向为90°时曲线形状由应变率为1200 s-1时的凹形变为凸形，曲线形状变化的原因是由于应变量增大，热软化效应使得孪

So there is rod configurational change in the deburring process.

在去毛刺过程中会变形软化。

The results showed that with increasing of FeS content,both the density and conductivity of composite were reduced,the hardness was increased and the microstructures were homogenized.When FeS content was less than 15% and more than 10%,the hardness of composite was conformably in this section.

FeS颗粒弥散强化Cu基复合材料是一类具有优异性能的新型功能材料，它具有高强度、高耐磨性、抗高温软化能力优良等综合物理性能和力学性能，同时兼顾了Cu的传导性，这与FeS的性能特征紧密相关。

The product contains abundant perilla essence, chamomile essence, gingko essence, aloe essence and other vegetable moisturizing ingredients to quickly complement moisture for shaved skin, soften corneum, resume skin health, prevent shave damage and skin roughness; firm and constringe skin, prevent moisture evaporation, make skin become clear and oil-free. The weak acidic, fragrance-free and pigment-free toner is the same mild to the sensitive skin.

本品内含丰富的紫苏精华、母菊精华、银杏精华以及芦荟精华等植物性保湿成份；为剃须后的肌肤迅速补充水份，软化角质层，恢复肌肤健康状态，预防剃须时的刮伤与肌肤粗糙；紧致收敛肌肤，防止水分蒸发，使肌肤清爽不粘腻，对敏感肌肤也同样温和低刺激的弱酸性化妆水，无香料无色素。

The product contains abundant perilla essence, chamomile essence, gingko essence, aloe essence and other vegetable moisturizing ingredients to quickly complement moisture for shaved skin, soften corneum, resume skin health, prevent shave damage and skin roughness; firm and constringe

功能： 本品内含丰富的紫苏精华、母菊精华、银杏精华以及芦荟精华等植物性保湿成份；为剃须后的肌肤迅速补充水份，软化角质层，恢复肌肤健康状态，预防剃须时的刮伤与肌肤粗糙；紧致收敛肌肤，防止水分蒸发，使肌肤清爽不粘腻，对敏感肌肤也同样温和低刺激的弱酸性化妆水，无香料无色素。

Both DSC and RMT150B experiment system gives continuous and stable curve of stress-strain including its post peak part.

扰动状态理论结果和RMT150B岩石实验系统得到的实验结果都可以给出稳定的、连续的、包括软化段的应力应变关系曲线。

With make up cotton is hit wet, brush the face that has washinging to go up, can bate is corneous, make skin more comfortable, can increase the absorption of follow-up product.

用化妆棉打湿，擦在清洗过的脸上，可以软化角质，使肌肤更舒适，并能增加后续产品的吸收。

Enhance Absorption Ability : Soften and remove corneous dead cells.

增强吸收力：软化及去除老化角质，增加肌肤吸收力。

The split between the two groups can hardly be papered over.

这两个团体间的分歧难以掩饰。

This approach not only encourages a greater number of responses, but minimizes the likelihood of stale groupthink.

这种做法不仅鼓励了更多的反应，而且减少跟风的可能性。