转速

With the map for example, we can obtained following conclusions: the cam turning speed has the most direct influence to the dynamics of valve rain; the cam profilers has also a very important influence, the cam profiler as the kind of compound pendulum dose not suit to high speed engine's valve train and the polydyne cam's characteristics is very different from compound pendulum cam's.

论文还首次利用多质量模型的特点对气门落座速度、气门落座冲击力及落座反跳等气门落座特性参数随凸轮轴转速和结构参数的变化规律进行了研究，考察了不同凸轮型线对上述特性参数的影响。对气门落座特性参数进行这样详细和全面的研究，是本论文的开创性工作之一，在其他的文献中尚未见相同报导。

The effects of different compounding conditions on the interlamellar space and mechanical properties of the composite were analyzed.

分析了不同工艺条件（主要为转子转速和喂料速率）对复合材料层间距及其力学性能的影响。

The results show that compressor rotating speed and speed ratio have important effect on the performance of the unit.

结果表明，转速和转速比对机组的性能影响较大。

The results show that when the porosity of sample was higher, compressure rate was higher and resilience rate was lower, however resilient rate of sample with higher porosity were increased notably when pressure was increased, and it tended to accord with of sample with lower porosity. The friction coefficient was higher when porosity of paper-based friction material was higher, and the friction coefficient tended to reduce and stabilize when braking pressure was increased. The friction coefficient of sample with high porosity tended to reduce and stabilize in continuous braking cycles.

结果表明：在相同载荷下，随着孔隙率增大，材料的压缩率增加而回弹率降低，随着载荷增加，高孔隙率材料的回弹率先明显增大，而后趋于稳定；在相同比压和转速下，孔隙率越高，材料的摩擦系数越大，随着比压增加，孔隙率高的材料摩擦系数逐渐降低，且不同孔隙率材料的摩擦系数逐渐趋于一致；在连续循环制动时，高孔隙率材料的摩擦系数逐渐降低并趋于稳定。

COMS some notebook full set of the more directly the work of set temperature and fan speed.

还有一些笔记本的COMS设置项较全，可以直接设置风扇工作温度和转速。

In general, the notebook fan speed can be adjusted through COMS setting to adjust the power-saving mode.

一般来说，笔记本风扇的转速可以在COMS设置里通过调整节电模式来调整。

The acoustic analysis results of axial configurative tongue design with aperture or comb shaped can reduce the BPF peak effects. Therefore we can not only receive better sound quality on the experiments, but also get a similar effect in fluent 6.2 simulations.

结果在声场分析方面，应用孔穴或梳状轴向舌端构形确有降低叶片通过频率声压峰值之效果，因此可获得较佳的音质优化程度，同时在fluent 6.2 中所模拟得到与穿孔型舌端有相近的结果趋势，且其出风口质量流率高转速时明显优於标准舌端

This research change axial configurative tongue design with aperture or comb shaped ; and adopt laboratory tests to verify its feasibility. The results be proved these different changes can decrease cross-flow fan BPF peak, in particular reduce 8 dB noise effects at specific rpm.

本研究提出改变状轴向舌端构形之设计，采以实验方法来验证其可行性且结果显示具梳状与穿孔形之舌端可有效改善横流扇之声音品质及BPF 基频峰值，在特定转速下可降低8dB之效果。

And the computation of pseudo-random numbers was programmed by multiplying the congruent number with the APDL language used. Taking account of the effects of original errors resulting from manufacture and the different working conditions such as rotating speed and load on the dynamic property of a bearing, the K-S inspection was done to determine the distribution of the data resulting from the virtual test and, consequently, the reliability was calculated with respect to the fatigue failure of bearings.

在此基础上，运用APDL语言实现乘同余数法产生伪随机数的计算程序，综合考虑轴承原始制造误差以及转速、载荷等不同工况对轴承动态性能的影响，对轴承进行多次随机虚拟试验，运用K-S检验法确定所获得的实验数据分布，求取轴承疲劳失效的可靠度。

Constant Angular Velocity mode and Constant Linear Velocity mode are integrated to build a single spindle motor control module to incorporate with long-seek servo. CAV mode and CLV mode are performed to show its feasibility. The experiment results showed that the pick-up-head can perform arbitrarily track-jump command, quite well.

此外，在主轴马达伺服部分，提出以跨轨旗标讯号来决定使用『碰-碰』控制法则让主轴马达转速变化的执行时间，也将主轴马达伺服中的等角速度控制模组与等线速度控制模组整合成功，形成单一的主轴马达控制模组，使与长寻轨伺服结合而更易於操作，让不论内、外寻轨的任意跨轨命令皆可以达成定线速度或是等角速度的控制目标。

Lugalbanda was a god and shepherd king of Uruk where he was worshipped for over a thousand years.

Lugalbanda 是神和被崇拜了一千年多 Uruk古埃及喜克索王朝国王。

I am coming just now,' and went on perfuming himself with Hunut, then he came and sat.

我来只是现在，'歼灭战perfuming自己与胡努特，那麼，他来到和SAT 。