转速

The results show that moist milling using absolute ethyl alcohol as medium and higher rotational speed can effectively decrease the particle size of Mo.

实验结果表明：使用无水乙醇作为球磨介质进行湿磨以及提高球磨的转速都可有效的降低Mo颗粒的尺寸。

After the airdrop experiments of the system of the projectile and speed-down parachute, the balance velocity obtained from the optics apparatus on the ground、the balance spinning speed obtained from the gyroscope on the projectile and the image obtained from the infrared detector on the projectile are all used to simulate the six-dimension exterior trajectory of the projectile and identify the roll damping moment derivatives, and the identification can safely come to a conclusion that the absolute value of roll damping moment derivatives from the engineering calculation are on the low side.

对卷弧尾翼弹与减速伞系统进行空投试验，由地面光测系统给出平衡落速、弹上陀螺给出平衡转速、弹上红外探测器拍摄地面图像判断弹的姿态。通过六自由度弹道模拟，对弹滚转阻尼导数进行参数辨识，得到工程估算所得滚转阻尼导数绝对值偏小的结论。 5。对空投试验中出现弹姿态摆动现象，从受力分析及红外图像分析两个方面进行探讨，给出合理解释，并根据分析对弹外形进行修改，在后来的试验中收到很好的效果。

Viscous fluid dynamometer is a kind of new power absorbing device featuring a mechanical characteristic of high braking torque under low speed, including zero speed.

液黏测功机是一种新型的功率吸收装置，具有低速（含0转速）输出大制动转矩的机械特性。

A proportional+forward scheme, in which the engine speed and the accelerator pedal position is the input, is proposed.

提出了一种以发动机转速和加速踏板位移作为输入参数的比例+前馈控制方案。

Study on continuous production of silica by hypergravity sulfuric acid precipitation method was conducted.

对超重力硫酸沉淀法生产白炭黑进行了连续化实验研究，通过改变硫酸的质量分数、旋转床转子的转速和硅酸钠的流量，探索出了这些工艺条件对白炭黑粉体性能的影响。

Torque motor have a quikly feedback and low rotate speed wave, can running smoothly in high torque and low speed situation.

力矩电动机反应速度快，转速波动小，能在高转矩低转速下稳定运行，机械特性和调节特性线性度好，具有高耦合刚度。

Such raw materials as waste polyethylent cable particles, pure polyvinyl chloride powder, wood powder, a metallic soap stabilizer, a coupling agent, chlorinated polyethylene and methacrylic acid polyesters and a lubricator are added into and mixed in a high speed mixer according to the formula, and the mixing temperature is 100 to 110 DEG C, the mixing time is 20 to 35 min; the well mixed material is added into an extruder for extrusion, the rotating speed of the mainframe of the extruder is 40 to 60r/min, the rotating speed of a feeding machine is 4 to 6r/min, and the materials are shaped after being extruded.

将废旧聚氯乙烯电缆颗粒、纯聚氯乙烯粉、木粉、金属皂类稳定剂、偶联剂、氯化聚乙烯、甲基丙烯酸多元酯、润滑剂按照配方配制的原料加入高混机中混合，混合温度为100℃～110℃，混合时间为20～35分钟；将混合好的原料加入挤出机中进行挤出，挤出机主机转速为：40～60转/分钟，喂料机转速为：4～6转/分钟；挤出后进行定型。

Most lathes provide from eight to eighteen speeds, usually in a geometric ratio, and on modern lathes all the speeds can be obtained merely by moving from two to four levers.

大多数车床有8～18种转速，一般按等级数排列。在现代车床上只需扳动2~4个手柄，就能得到全部挡位的转速。

Although the torque figure is uninspiring, 85 percent of the maximum torque (340 Nm/250 ft-lb) is available from 2000 rpm up to 6,500 rpm creating an almost flat torque curve across this wide rev range.

虽然扭矩数字是令人鼓舞，百分之八十五的最大扭矩（ 340 Nm/250英尺磅），可从2000年每分钟转速高达6500转创造一个基本持平扭矩曲线在这个全转速范围内。

The paper uses the strategies of pitch angle control and rotational speed control. For the rotational speed controller, vector control method in the dq synchronous rotational frame was employed.

系统采用了桨距角控制和发电机转速控制策略，而发电机转速控制采用了dq同步旋转坐标系下的矢量控制。

It has been put forward that there exists single Ball point and double Ball points on the symmetrical connecting-rod curves of equilateral mechanisms.

从鲍尔点的形成原理出发，分析对称连杆曲线上鲍尔点的产生条件，提出等边机构的对称连杆曲线上有单鲍尔点和双鲍尔点。

The factory affiliated to the Group primarily manufactures multiple-purpose pincers, baking kits, knives, scissors, kitchenware, gardening tools and beauty care kits as well as other hardware tools, the annual production value of which reaches US$ 30 million dollars.

集团所属工厂主要生产多用钳、烤具、刀具、剪刀、厨具、花园工具、美容套等五金产品，年生产总值3000万美元，产品价廉物美、选料上乘、质量保证，深受国内外客户的青睐