转角

The method of dimension synthesis for the path of connecting rods of crank slider mechanism with predetermined time scale by using rotation angle operator of connecting rods is proposed in this paper.

提出了利用连杆转角算子对带有预定时标的曲柄滑块机构连杆轨迹进行尺度综合的方法。

Based on a constant value of gravitational acceleration at a given location of the earth and accurate measurement of tilting angle of the table, a calibrating method and procedure for primary parameters of accelerometers, i.e.

基于地球上给定地点的重力加速度为一恒量和转角的准确测量，给出了加速度计主要参数（灵敏度、线性度和横向灵敏度）的标定方法和步骤。

When solving IK, we use position constraint of the knee joint to decide the swivel angle. The result obtained in this way can preserve the continuousness and the detail signal of the original data.

在求解IK的过程中，使用膝关节的位置约束来确定旋转角φ，求解结果保持了解的连续性和原始数据的细节信号。

Displacement of earth bag during sinking down and specialties of sinking of lead cage. This paper analyzes characters of long tube bag in the same direction and contradictorily.

分析了长管袋在垂直水流方向和顺水流方向抛掷的受力特点，并推出了管袋位移及转角公式。

By comparison with the influence of safety factors,nominal height, corner quantity, and geological condition on project cost for 110 kV steel tubular pole structures overhead transmission line, the paper gives the recommendation values of safety factors for conductor and ground line design.

中文摘要：通过对110kV钢管杆架空线路安全系数的不同取值、不同呼称高、线路经过的不同转角数量和不同地质条件对工程造价的影响进行分析比较，提出了线路设计导、地线安全系数的推荐值。

And this paper assumes that resisting power is accordwith parabola, gets all arch as basic configuration, gets formulation from the condition that therelative corner , horizontal displacement and vertical displacement of vault section iszero,adds deformation condition of maximum resisting power and zero resisting power, solvesequation group to get the internal force of lining . And lining internal force computing methodunder bias load based on assumed resisting power method is formulized.

本文假定弹性抗力按二次抛物线分布，取全拱为基本结构，由拱顶截面的相对转角、相对水平位移和相对垂直位移为零的条件列出变形协调方程，再增加最大弹性抗力处的变形协调条件和弹性抗力为零处径向位移为零的变形协调条件，解方程组求解得出衬砌结构的弹性抗力分布及内力。

Relation between geometrical contour error of inner corner and machining condition is investigated by the experimental plan of Taguchi quality design. Through the quantitative analysis, the geometrical contour error is mainly affected by wire tension and flushing pressure. By regression analysis, a mathematical model is established to estimate cutting path error of corner cutting. According to the estimated cutting path error, the program path is corrected.

研究首先以田口式品质设计实验计画法来探讨加工参数与隅角形状误差间的关系，从变异数分析的结果得知，线张力与冲水压力是对於隅角精度影响最显著因子，应用回归分析建立转角加工路径误差量估测模式，利用此模式以预测不同加工条件下隅角加工路径误差量，依据预测加工路径误差量计算轨迹补偿量，实验结果证明本文所提出轨迹补偿策略可有效提高60%之隅角加工精度。

To install the fixed filler on the corner cabinet, use a ф4.2MM drill to drill a hole on the bottom panel at a place near the fixed filler. Use pneumatic screwdriver to turn at the hole positions to form countersink holes. Use 4*50 self-tapping screws to secure the fixed filler on the bottom panel. Keep

转角柜固定封板的安装，先用ф4.2MM的直钻在柜底板靠近固定封板处打孔，/然后用风批头在打孔处转动几下形成螺钉沉孔，再用4*50的自功钉把封板固定在柜底板上/安装可调脚将柜底保持朝上，然后正面进入50MM画线并装好柜脚座。

And later, on the corner of 73rd and mea culpa...

稍后就在73街转角上

Constant amplitude reversed cyclic load tests were simulated with the aid of software MSC/Fatigue. Fatigue life predictions can be made for this class of connection using relationships analogous to the well-known Manson-Coffin strain-life equation for metals.

本文使用MSC/Fatigue软件进行了常幅偏移下的性能分析，类似于著名的Manson-Coffin公式，建立了所研究节点的塑性转角和寿命的关系。

The split between the two groups can hardly be papered over.

这两个团体间的分歧难以掩饰。

This approach not only encourages a greater number of responses, but minimizes the likelihood of stale groupthink.

这种做法不仅鼓励了更多的反应，而且减少跟风的可能性。