转动方向

The system adopted active tracking,namely calculate the input angle of the tracking device in advance,the angle is correspondent to the sun position some moment.Photoelectric sensors react the sunlight that putting on different position of the platform, feedback electrical signal.Then single-chip applys the subprogram and sends out pulse to step motors according to the signals,can control the rotate angle and direction of the step motor. The mechanism has realized the automatic track to the sun, so that the trackers top flat board can be always vertical to the sunlight and arrive the furthest receiving energy.

系统采用主动式跟踪，即预先计算好对应于某时刻太阳位置的跟踪机构的输入角度，通过跟踪器上平台不同位置上摆放的光电传感器感受该太阳位置的光照，反馈回电信号，单片机根据该信号调用子程序发出脉冲对步进电动机的转动角度和方向进行控制，实现了机构对太阳的自动跟踪，使跟踪装置的上平台始终处于垂直于光照方向，达到了能量最大限度的接收。

This ellipsometric method does not need to rotate the sample azimuthally. The physical parameters of sample are measured under various linear polarized lights through the numerical fitting to its theoretical model. In addition to the orientation of the first layer of nematic liquid crystal is considered, the total phase retardation and twist angle of twist Nematic Liquid Crystal cell are the physical parameters measured by this method.

本论文以椭圆偏极术为基础，在不需转动样本方位角的情况下，以不同偏振方向的线性偏振光入射样本，藉由出射光偏振态的变化，用数值方法拟合出样本矩阵模型参数；我们所量测的样本为扭转式液晶盒，其矩阵模型包含了三个参数：总相位延迟、扭转角及第一层液晶锚定方向。

As you move these sliders to the right the response becomes non-linear. In this case, the first 50% deflection of your joystick or yoke may only deflect the aircraft's controls by 10%. This will dampen any aircraft movements and desensitize your controls but keep in mind that the remaining 90% of the control surface deflection must take place in the last 50% of joystick travel, in this case.

如果把他们都拉到右边，那么这些控制将变成非线性的（译者注：就是说你把摇杆向一个方向移动很大距离时，才会慢慢开始加速转动），如果拉到100%，那么当你朝一个方向移动50%摇杆的时候，只相当于滑块在0%时的10%的效果。

So we suggest a new method for the measurement of d〓 according to the SHG conversion efficiency at some non-phase-matching direction, the optimum focus parameter ofNPM SHG was given also.

在KTP晶体球中第Ⅰ类PM SHG实验中，我们通过转动晶体球，直接根据谐波输出的强度得到了SHG的相位匹配方向，从而避免了折射率测量或色散方程计算的误差，并得到了精确的KTP晶体完整的第Ⅰ类PM曲线，以及相应PM方向的有效非线性系数d〓，根据这个测量结果，我们对文献报道的六组色散方程进行了比较，认为由Vanherzeele和Bierlein给出的色散方程拟合精度最高。

Structure form adopts converse triangle beam double-hole connection welded by general electric trolley wall plate and steel plate, connection shaft, triangle beam bottom is connected with girder by nut and thrust bearing, triangle beam could rotate 360 degrees horizontally, thus realize whole set electric trolley horizontal rotation, largely reduce curve track curvature radius of electric hoist traveling mechanism.

描述： 结构形式采取通用电动小车墙板与一个钢板和连接轴组焊的倒三角形吊梁双孔连接，三角吊梁下面通过螺母及推力轴承与一个横梁连接，三角吊梁相对横梁可在水平方向做360度旋转，从而实现电动小车的整体水平方向转动，大大减小了电动葫芦运行机构弧形轨道曲率半径。

According to the rotate speed and orientation of interface set motor, control motor drives the trolley minus rotation. Then, drive the rocket bomb rotation. The displacement sensor measures the core flopping in real time.

其根据人机界面设定电机的旋转速度和方向，控制电机以设定速度和方向，带动火箭弹支撑滚轮副转动，从而带动火箭弹全弹旋转，位移传感器对相对于定心部的跳动进行实时测量。

The spindle speed can be easily specified and the spindly can be turned on in a forward or reverse direction.

主轴速度的指定很简单。主轴可丄方向转动，也可反方向转动。

Those angelic beings moved in whatever direction they wanted to. The wheels within wheels did not need to turn one way or the other.

那些活物能够按照自己的心意，往任何想去的方向转动；但轮中的轮却不必向任何一方转动。

Comparing the magnetic properties of sintered magnets from HD powders and the degassed powders, it is found that the sintered magnet from HD powders gets excellent properties at a temperature of 20～30℃ lower than the magnet from the degassed powders.

例如，HD磁粉在10T的外磁场下所受到的转动力矩甚至还没有350℃脱氢磁粉在2T磁场下受到的力矩大，当磁粉的c轴与磁场方向成π/5（36°）角度时，两者受到的转动力矩分别为1.123×10〓Nm和1.202×10〓Nm。

The feeding head can rotate around axial Z and axial X or Y. With the help of Siemens NC system, which can overcome the limitations of feeding heads working space, we can make axle sleeve and so on. It can be used to repair irregular shape products in laser cladding, such as metallic sheath. Using 3D coaxial feeding head, large area laser refabrication was carried out in metallic sheath.

由于原数控系统是非开放性的，不宜直接在原有系统上进行二次开发，考虑到现有条件，采用单片机控制二步进电机以实现送粉头能绕Z轴转动和绕水平轴转动，加上原有数控系统的在Z轴方向上的运动配合使送粉工作头具有三维空间工作能力，它克服了普通送粉头工作空间的限制，同时还具有粉末流束焦点可调功能。

In the negative and interrogative forms, of course, this is identical to the non-emphatic forms.

。但是，在否定句或疑问句里，这种带有"do"的方法表达的效果却没有什么强调的意思。

Go down on one's knees;kneel down

屈膝跪下。。。下跪祈祷