轧制

The paper describes a new process of electrolytic decomposition and electrical concreting waste emulsion for by DC under certain temperature.

研究了在一定温度条件下，利用直流电源对轧制铝板中用过的废乳液进行电解破乳和电混凝的新工艺。

The temperature of bar, rolling force and power of mill drive motor were thus modeled to analyze the causes of bar crooking/heaping, such as the decreasing internal stress due to reduced bar size enables the head of running bar to be lower than the baffle of flying shear, crook and heap.

通过研究小圆钢温度、轧制力和电机功率模型，分析了小圆钢在飞剪处由于直径变小，内应力的降低，容易形成低头，使向前运动的小圆钢头部低于挡板造成堆钢的过程。

Though the application of these techniques, the turbulences of the strip flux and the tension resulted in all kinds of interferences are debarred, ensuring the rolling all right and improvement of the strip quality.

通过这几种技术的应用，解决了各种干扰所导致的带钢流量和张力的扰动，保证了轧制顺利和带钢质量的改善，成材率由原来的94%提高到98%。

It is shown that uniform powder cloth with proper thickness can be produced by using appropriate rolling parameters. Thermogravimetic and pyrolysis residuum analysis indicate that the burnout process of fugitive binder used to produce the cloth is found to take place in two stages, no residuum is left when degassed properly.

结果表明，采用合适的轧制参数即可容易地获得厚度合适、均匀的粉末布；热失重分析和热解残余物分析指出用来制备粉末布的有机粘结剂的去除过程分成两个阶段，合理除气后，基本没有残余物。

This welding wire not only has the inherent properties of metal powder-cored wire, such as with better welding quality, without slag, highly efficiency and conveniently adjusting the alloying elements etc., but also has the advantage of low hardness in as-welded (less than HRC45), good machinability, high hardness in as-aged (more than HRC55) and better wear resistance with customary working procedure on making or repairing equipments such as rollers when reasonable designing the alloys content. The author adequately makes use of the high-tempering in the required stress relieving working procedure. During this working procedure, which causes the hardness of overlaying metal increased by the reason of austenite changes into tempered martensite and more chiefly what is the precipitation of a lot of carbide by secondary hardening simultaneously. This wire can solve the hard rolled problems of some solid wires with higher alloys while it can get over the conflict of existing overlaying materials what are always possesed high hardness with poor machinability or low hardness, good machinability with poor wear resistance. Further, it also can overcome the intenerating phenomena between welding beads and make the external hardness of overlaying metal uniform. Be sure it could be found important meaning in the overlaying of wear-resistant equipments, such as the precise roller.

该焊丝除了具有金属粉型药芯焊丝焊接质量好、无渣、高效率和合金成分可方便调节等固有的优点外，合理的设计粉芯中的合金成分，按通常工序制造与修复轧辊等设备，充分利用必需的消除应力工序的高温回火，堆焊层金属在奥氏体转变为回火马氏体的同时更主要是通过二次硬化析出了大量碳化物导致硬度增加，使得该焊丝还具有焊态硬度低(小于HRC45)、机加工性能好和时效态硬度高(大于HRC55)、耐磨性能好等优点，解决了某些高合金实芯焊丝轧制困难的问题，同时克服了现行堆焊材料硬度高、加工性能差或者硬度低、加工性能好、耐磨性差的矛盾，并能克服焊道之间的软化现象，使堆焊表面硬度较为均匀，对耐磨件，譬如精轧辊的堆焊具有重要意义。

Twin lamellae will be deformed differently when rolling in different direction.

在轧制过程中，超细孪晶以孪晶界的迁移方式收缩并消失。

The stability tension of laminating production system is the key to successful operations and required product quality.

0引言贴纸铝箔又称烟泊，是香烟包装的主要材料。烟泊是通过轧制铝箔与衬纸的连续复合而生产的。

An ultra-high strength, weldable, low alloy steel with excellent cryogenic temperature toughness in the base plate and in the heat affected zone when welded, having a tensile strength greater than 830 MPa (120 ksi) and a micro-laminate microstructure comprising austenite film layers and fine-grained martensite/lower bainite laths, is prepared by heating a steel slab comprising iron and specified weight percentages of some or all of the additives carbon, manganese, nickel, nitrogen, copper, chromium, molybdenum, silicon, niobium, vanadium, titanium, aluminum, and boron; reducing the slab to form plate in one or more passes in a temperature range in which austenite recrystallizes; finish rolling the plate in one or more passes in a temperature range below the austenite recrystallization temperature and above the Ar3 transformation temperature; quenching the finish rolled plate to a suitable Quench Stop Temperature; stopping the quenching; and either, for a period of time, holding the plate substantially isothermally at the QST or slow-cooling the plate before air cooling, or simply air cooling the plate to ambient temperature.

在基体板以及焊接时的热影响区处的低温韧性优异的超高强度、可焊接、低合金钢具有高于830MPa（120ksi）的抗拉强度，并且具有包含奥氏体薄膜层和细晶粒的马氏体／下贝氏体板条的显微层状组织，所述钢的制备过程为：加热含有铁以及特定重量百分比的添加元素的钢坯，所述添加元素为碳，锰，镍，氮，铜，铬，钼，硅，铌，钒，钛，铝，以及硼中的一些或全部；在奥氏体可发生再结晶的温度范围内，采用一个或多个道次，将所述钢坯轧制成板材；在低于奥氏体再结晶温度但高于Ar 3 转变点的温度下，采用一个或多个道次对所述板材进行终轧；将所述终轧板材淬火至一适当淬火终止温度；停止所述淬火；或者在空冷前在QST点基本等温保持所述板材一段时间，或者对所述板材进行缓慢冷却，或者只是简单地将所述板材空冷至室温。

We have developed a full range of the rolling process models, which are the most accurate and most robust process models for roll design in this field.

我们已经制定了一个全系列的轧制过程模型，是最佳过程模型系列之一，尤其在该孔型设计领域。

Glass ,cast or rolled (excl. safety glass), coloured, opacified or flashed during manufacture, not further worked, non-wired, in sheets

玻璃板材，在制造过程中经着色、遮光或套色，压铸或轧制的，未经进一点加工，无金属丝

The split between the two groups can hardly be papered over.

这两个团体间的分歧难以掩饰。

This approach not only encourages a greater number of responses, but minimizes the likelihood of stale groupthink.

这种做法不仅鼓励了更多的反应，而且减少跟风的可能性。