轧

The best technology parameters of rolling 6 mm Pb for experiment milli are 130/130 roll diameter, eduction 5%, angle of entrance -3°, roll rotational velocity 164 rpm.

实验轧机控轧6 mm铅板头部翘曲的最佳工艺参数为上下轧辊直径比1：1，压下率5%，导入角-3°，轧辊转速164 r/min。

The web paper is inputted by Mill Roll Stand, and after heated and regulating the moisture by the pre-heater, the paper is put into the Single Facer for shaping and then conglutinating with another top paper to form a single corrugated board. The single corrugated board is then transmitted by the overhead bridge conveyor to multiple heater to be reheated, after this the paper is to double facer for being heated and jointed, herein a continuous corrugated board is formed.

由原纸架输入卷形原纸，经过热缸机加热及调节湿度，进入单面瓦楞机，经过瓦楞机的滚轧成形，与另一面纸粘合成单面瓦楞纸，由天桥架传送，经多重预热器再次加热，经上浆机粘糊再至双面机加热贴合，此时连续的瓦楞纸板即已成形。

New Area are using the 2250 continuous casting and rolling production line, fan-shaped casting is paragraph one of the key parts.

新区现使用的是2250的连铸连轧生产线，连铸扇形段乃是其中的关键部位之一。

Based on the analysis to crankshaft-working system and turning/feed system for cold pilger mill and radio of two turning angles, the system is designed with computer.

本文通过对双回转送进二辊冷轧管机的曲轴机架与回转系统进行分析，以保证工作行程和轧件两次回转角分配比为设计前提，按照回转凸轮轮廓曲线的两过渡段的峰值加速度相等的设计准则，计算曲轴-机架与回转系统，实现了系统的最优化的设计。

Wu an ping tune with the music is relatively simple at first, thereer xian (commonly known as small fiddlestick), rolling Guoqin, Banhu, known assan da jian , then gradually add the erhu, Zhonghu, cello, Sheng, flute, etc. Suona.

武安平调的伴乐起初比较简单，有二弦、轧琴、板胡，号称三大件，后来逐步增添了二胡、中胡、大提琴、笙、笛、唢呐等。

The rolling procedure of cross wedge rolling in the case of die void and not was simulated adopting Finite element method. Base on it, effect of die void on rolling force was analyzed in detail.

为此，采用有限元法对楔横轧模具在不脱空和脱空情况下进行了轧制过程数值模拟，详细分析了模具脱空对轧制力影响的规律，得到了在一定断面收缩率范围内模具脱空有利于减小轧制力的研究结果，并与测试结果进行比较。

The important machines are conditioner, jet dryer , cracker, flaker, the construction and process parameters of these machines are analyzed.

对其中的关键设备调质器、喷气干燥器、破碎机、轧坯机的结构及工艺参数作了分析比较。

This was just a short squeeze of absolute epic proportions,' said Stephen Schork, author of a daily energy market report and a former Nymex floor trader.

每日能源市场报告的作者、曾是纽约商品交易所场内交易员的斯蒂芬。施洛克称，这是一次绝对历史规模的轧空。

When the forward slip difference is large,the influence of velocity difference is small and workpiece is easily bent.

经试验结果分析，弯曲是轧件上、下表面前滑差和速差综合作用的结果。

New multi—objectives function (including mill stand longitudinal stiffness, distribution coefficient of loaded pressure between rolls, weight of mill stand, rolling power, rolls loaded gap profile changeability of bending force, transverse mill stand stiffness of bending force, transverse mill stand stiffness of rolling load) multi—constraints (including rolls strength, spindle strength, backup roll bearing load, minimum rollable gauge, roll surface temperature rise) rolls system parameters optimization model of four—high cold strip mill is established, and programme for mill structural illustration creation on the platform of AutoCad designs is compiled. With this as basis, rolls system parameters of Yichang thin strip corporation's 1219 cold mill are calculated using SUMT (subsequent unconstrained minimization technology).

本文建立了以板形和板凸度控制特性为目标的四辊轧机多目标函数（包括轧机纵向刚度、辊间压力分布系数、轧机重量、功率、弯辊力对轧机辊缝形状改变能力、对弯辊力的横向刚度、对轧制力的横向刚度）、多约束条件（包括轧辊强度、接轴强度、支承辊轴承负荷、最小可轧厚度、轧辊温升等）的辊系参数优化模型，以此模型为基础，利用惩罚函数法计算了益昌薄板公司1219冷轧机辊系参数，编制了AutoCAD平台下的轧机结构示意图自动图形软件。

But we don't care about Battlegrounds.

但我们并不在乎沙场中的显露。

Ah! don't mention it, the butcher's shop is a horror.

啊！不用提了。提到肉，真是糟透了。