车辆轴

Drawback occurred in the classical VSSMC can be alleviated in the proposed control scheme because of importing the eliminating chatterer. According to the control strategy put forward above, corresponding controller for ABS is designed.

利用BOLTMANN-HAMEL方法所推导的双轴车辆动力学方程，可开环或闭环模拟转弯制动车辆的操纵稳定性，特别在分析ABS对车辆转弯制动性能的影响或VDSC系统研究中有重要作用。

It is original to use piezoelectricity sensor getting the vehicular information including the number of tyre and axle.

用压电传感器来实现多种车辆特征的测量，包括车辆的轮数、轴数。

The primary reasons for a tracked vehicle's compactness are reduced suspension clearance, wheel turning clearance, and the absence of multiple transfer cases and drive shafts that are integral to the design of multiwheeled vehicles.

首先，履带车辆的因为减小了悬挂机构、转向机构并取消了多轮驱动轮式车辆所必不可少的并联的变速箱和驱动轴，因此其外形要比轮式车辆更紧凑。

The land vehicle that is defined in claim 11, wherein said airfoil system includes at least three substantially vertical airfoils, said one airfoil being located essentially in a vertical plane containing the longitudinal axis of the vehicle, and the other two vertical airfoils being located at generally parallel relation to said one airfoil on opposite sides thereof rearwardly of the center of gravity of the vehicle.

土地车辆是指在索赔11 ，其中说，翼型系统，其中至少有三个大大的垂直翼型说，一翼型位于基本上是在一个垂直平面载有纵向轴的车辆，和其他两个垂直翼型正位于普遍平行的关系说，一翼型对对立面存在的rearwardly该中心的重心的车辆。

Our main products are as following: Container transportation semi-trailer(frame of platform ＆ two or three axles),low platform semi-trailer,bulk cement powder tank truck and semi-trailer, semi-trailer tipper, oil tank semi-trailer、car transportation semi-trailer、cement mixer semi-trailer and dry box truck ＆ semi-trailerand the hydraulic pressure heavy type transportation trailer of many axles lines.

公司主要产品有40英尺二轴或三轴集装箱骨架及平板半挂车、二轴或三轴低平板半挂车、码头集装箱运输半挂车、散装水泥罐式汽车及半挂车、自卸汽车及半挂车，运加油车及半挂车、车辆运输半挂车、混凝土搅拌运输半挂车、厢式运输半挂车和多轴线液压重型运输车等九大系列五十多个品种。

Our main products are as following: Container transportation semi-trailer(frame of platform ＆ two or three axles),low platform semi-trailer,bulk cement powder tank truck and semi-trailer, semi-trailer tipper, oil tank semi-trailer、car transportation semi-trailer、cement mixer semi-trailer and dry box truck ＆ semi-trailerand the hydraulic pressure heavy type transportation trailer of m any axles lines .

公司主要产品有40英尺二轴或三轴集装箱骨架及平板半挂车、二轴或三轴低平板半挂车、码头集装箱运输半挂车、散装水泥罐式汽车及半挂车、自卸汽车及半挂车，运加油车及半挂车、车辆运输半挂车、混凝土搅拌运输半挂车、厢式运输半挂车和多轴线液压重型运输车等九大系列五十多个品种。

Aiming at this problem, firstly, calculation formulae of utilization adhesion coefficient after installment of retarder were detailedly deduced. Then braking force distribution ratio , braking intensity and vehicle full-load parameters were taken as variables and inequalities which are about of retarder braking force , braking force distribution ratio , braking intensity and vehicle full-load parameters were established based on the ECE Law. The range of corresponding to any , as well as the most optimal matching between them, were obtained by solving these inequalities.

为此，论文在推导了安装缓速器后前、后轴利用附着系数、的计算公式基础上，基于ECE法规要求，以制动力分配比、制动强度及车辆满载参数为变量，建立了缓速器制动力关于车辆制动力分配比、制动强度和满载参数之间的多元不等式组，通过求解多元不等式组获得缓速器制动力与制动力分配比之间的取值关系，并从中得到二者之间的最优匹配。

A motor vehicle gear-type transmission has an input shaft clutch, multiple gear pairs, multiple mesh units, and an input shaft clutch actuator which adjusts the position or pressure load of the pressure member of the input shaft clutch.

车辆用齿轮式变速机(50)是由输入轴离合器(7)、多个齿轮对(1、2、3、4、5、11、12、13、14、15)、多个啮合机构(21、22、23)和调整输入轴离合器(7)的压紧部件的位置或压紧负载的输入轴致动器(61)所构成。

In case of rear wheel drive and four wheel drive vehicles drive train vibrations can be reduced by balancing the flange of the rear axle differential to give more driving comfort and an improved life of the vehicle .

如果能够平衡后轴法兰，就能减少后轮驱动以及四轮驱动车辆驱动部分的振动，并能不同程度增加驾驶舒适性，延长车辆寿命。

This paper gives a thoeretical analysis on the standard currently adopted in China for the widening of railway track gauge on curves, and points out that this atandard does not tally with the railway oparational actuality, the calculation data used are not in conformity to the present rolling stock conditions in this country and that the marginal radius and the amount prorided for the widening of curved track gauge are on the large side.

本文对我国现行曲线距轨加宽标准进行了理论分析，指出它脫离运营实际，而采用计算数据又不符合我国现有车辆情况，加宽起始半径和加宽值都偏大。提出在理论上比较切合实际的计算方法是车辆按力学自由內接条件计算；机车和少数固定轴距大的车辆，按最小运营半径条件检算，制订我国的曲线轨距加宽新标准。

This paper discusses design and realizable methods of remote test output interface from logical design angle.

本文从逻辑设计的角度讨论遥测输出接口的设计及实现方法。

This also 星体投射plies to buildings, structures and geological features.

这也适用于建筑物和地质特征。