距

Based on the theoretical analysis for 1000 m long drainage skills, the UDEC4.0 numerical simulation software is adopted to perform the calculation, showing that the height of caving zone and fractured zone of gob is 9 m and 30 m, the vertical height from the mining induced O-shaped circle to the roof is 10~25 m, and the horizontal distance to both sides of gob is 10~35 m.

本文在顶板千米钻孔抽采技术原理分析的基础上，采用UDEC4.0数值模拟软件计算得出采空区冒落带和裂隙带高度为9m和30m，采动裂隙&O&形圈的范围为距工作面顶板垂高10~25m，距采空区两侧水平距离为10~35m。

It was offered with two wheelbases, a short wheel base of 2400 mm and a long one of 2850 mm.

有人提出两个轴距，短轴距的2400毫米和长期之一的二千八百五毫米。

With the finite element method this *** analyzes influence factors of Lateral rigidity including layout and spacing of faade bracing, horizontal bracing and unusual arrangement of faade bracing firstly, revealing the change discipline of lateral rigidity. Then, on this basis, this *** further researches on frame Stability capacity and its influence factors such as semi-rigid node, bracing spacing, base transom height, distance between top transom and the supported matter, structure height, longitudinal distance between adjacent standards, distance between adjacent transoms, horizontal load, in order to find out the law of stability capacity, guiding the design and construction.

借助有限元本文首先分析立面斜杆的布置方式、布置间距、水平斜杆以及立面斜杆不正常布置等因素对架体抗侧刚度的影响，揭示抗侧刚度的变化规律；在此基础上，进一步考查了节点半刚性、斜杆间距、底排横杆高度、顶杆伸出长度、架体高度、立杆纵距、横杆步距、水平荷载大小等对架体稳定承载力的影响，以期得到承载力的变化规律，用来更好地指导设计和施工。

Curve and the x, y-axis intersection (a, 0),(0, b) where a curve is called the intercept in the x-axis; b is called the curve y axis intercept .

曲线与x、y轴的交点（a，0），（0，b）其中a叫曲线在x轴上的截距；b叫曲线在y轴上的截距。

Curve and the x, y-axis intersection (a, 0),(0, b) where a call in the x-axis intercept curve; b is called the curve y axis intercept .

曲线与x、y轴的交点（a，0），（0，b）其中a叫曲线在x轴上的截距；b叫曲线在y轴上的截距。

For optimum wear life, centre distance between two sprockets should normally be within the range 30 to 50 times the chain pitch.

为了获得最佳磨损寿命，2个链轮间的中心距通常应是链条节距的30至50倍。

The computationresults show that for a organ-pipe nozzle with a given configuration size, the nondimensional axial velocity attenuates slower with the increase in stand-distance, and the nondimensional axial velocity attenuation pattern remains the same, and the nondimensional axial velocity along the jet centerline attenuates slower with the increase in distance between the nozzleexit and the impinging plate.

计算结果还表明：对给定结构尺寸的风琴管喷嘴，随着喷距的增加，沿径向的无因次轴向速度衰减变慢、沿径向无因次轴向速度衰减规律不随喷速的变化而变化；无因次轴心速度的衰减规律随着喷嘴出口到井底间距离的增大，射流轴心速度衰减变慢，但其变化幅度不大；在固定靶距情况下，无因次轴心速度衰减规律不随喷速的变化而变化。

It is capable of real-time parallel capture of the three seeders' seeding status by using the independent capture of the three base colors red, green, and blue of the colorized image. It is also capable of joining serial images by using image-matching techniques based on the signs.

种子粒距的检测是进行精密播种机性能检测的关键步骤，目前国内外的种子粒距检测主要以光电检测手段为主，通过记录两粒种子落下的时间间隔和地轮前进的速度来计算种子的间距 [5～ 7，12 ]。

Lift the suspension coop to the distance over 3m far from the pillar( that is 1m far from safety inserting block to the pillar).

5.5。将吊笼上升到距顶梁大于3米处停止（即安全插块距顶梁1米处）。

At this level, you have not to add too many details in your write-hand "draft": size of every single element, paddings, borders and margins are enough.

在这一流程，你不需要在你的手写&草稿&上增加太多的细节：每个标签的大小（width，以pixel或percentage的形式），内边距，边框和外边距就足够了。

And Pharaoh spoke to Joseph, saying, Your father and your brothers have come to you.

47：5 法老对约瑟说，你父亲和你弟兄们到你这里来了。

Additionally, the approximate flattening of surface strip using lines linking midpoints on perpendicular lines between geodesic curves and the unconditional extreme value method are discussed.

提出了用测地线方程、曲面上两点间短程线来计算膜结构曲面测地线的方法，同时，采用测地线间垂线的中点连线和用无约束极值法进行空间条状曲面近似展开的分析。