起模

The results show that more modalities can be excited from asymmetric system and that there is little difference between the power flow spectra of rigid raft system and flexible raft system in middle and low bands of frequency, but there is considerable difference at high frequency.

研究结果表明，非对称系统能激励出更多的模态；在中低频段弹性浮筏系统和刚性浮筏系统的功率谱没有很大的区别，但是在高频段差别则很明显，浮筏的弹性模态起着主要作用；减小隔振器的刚度并适当增加隔振器阻尼不仅可以降低传递到基础的功率谱，同时还可以抑制共振减小冲击。

With simplified assumption made for the modal trial mass ratio and the linear response char acteristic of the holobalancing technique, the transfer matrix corresponding to a certain correction plane then is extended to the trial set transfer matrix, which is related to a certain order of modal trial mass set. The number of trial runs necessary for the balancing operation is reduced and the balancing efficiency is improved.

借鉴Darlow混合法中模态试重组的思想，通过对模态试重比的简化假设，利用迁移矩阵的线性可叠加性将对应于某单一平衡面的迁移矩阵扩展为对应于某阶模态试重组的迁移矩阵，从而减少了平衡高阶不平衡量所需的试重起车次数，提高了现场平衡效率，且平衡效果良好。

The result shows that the mechanism of secondary instability does work, no matter the fundamental wave is first mode or second mode T-S wave.

结果显示，不论基本波是第一模态还是第二模态的T-S波，二次失稳机制都起作用。

The results show that AREEC liquid crystal enables the flow behavior of PC to change from quasi-Newtonian type to pseudo-plastic type, and it can act as heterogeneous nuclei to accelerate greatly crystallization of PET, and then to improve evidently their injection moldability.

将AREEC液晶与PC、PET熔体共混，研究了共混体系的流变行为、结晶特性和可模塑性，证明AREEC液晶能使PC流变行为由准牛顿型变为假塑性幂律型，能对PET起异相成核和显著加速结晶作用，从而大大改善它们的注塑可塑模性。

The result of optimization and analysis show: 1 across-axis sensitivity is smaller, less than 2% of the primary axis sensitivity; 2 the first mode is dominant at primary axis, which reduce intersectional coupling; 3 when damp ratio is between 0.3 and 0.7, accelerometer has better dynamic characteristic.

分析结果表明此种结构的具有：1横向灵敏度小，X、Z方向的横向灵敏度均不到敏感方向的2％；2在敏感方向上，一阶模态起主导作用，其它模态的影响较小，有利于减小交叉耦合的影响；3当阻尼比毛为0.3—0.7时，传感器具有较好的动态特性。

In October 2006 also on their own research and development of Diamond Wire Drawing Die diamonds, has a few have the strength of the domestic die enterprises to establish business relationship, is most welcome.

于2006年10月又自行研究开发金刚石拉丝模钻石，已与国内几家有实力的拉丝模企业建立起业务关系，深受欢迎。

If the blank is wrinkling on the blank holder surface, the cause is most likely one of four factors: insufficient blank holder force; a poor fit between the die face and blank holder surface; an equalizer block that is holding the die face apart from the blank holder surface; or severe blank holder deflection.

如果板料在压边面上起皱，绝大多数起因是后面四个因素之一：不充分的压边力；凹模和压边圈表面不良的匹配；凹模和压边圈间的平衡块；或者是压边圈的严重变形。

If the blank is wrinkling on the blank holder surface, the cause is most likely one of four factors: insufficient blank holder force; a poor fit between the die face and blank holder surface; an equalizer block that is holding the die face apart from the blank holder surface; or severe blank holder deflection.

如果展开平板在压边圈面上起皱，绝大多数起因是后面四个因素之一：不充分的压边力；凹模和压边圈表面不良的匹配；凹模和压边圈表面间的平衡块；压边圈的变形。

Because of the unique fitting mode of hydraulic drawing, early wrinkles of conical parts (very likely to wrinkle in ordinary deep drawing) fit orderly to punch under the action of counter pressure as the punch moves down ward, thus wrinkle-free parts can be obtained.

由于充液拉深方法独特的贴模方式，使普通拉深方法极易起皱的锥形件成形初期产生的皱随着凸模向下运动在对向液压的作用下顺次贴向凸模，从而可以得到无皱的零件。

In addition, the blank holding force that is required to avoid wrinkle and rupture during conical part deep drawing is researched. The necessity of reasonable blank holding force in pressing is expounded. From the view of mechanical analysis, the wrinkle critical condition of side-wall is derived for the first time by the stress state of side-wall, the main deformation region on blank. According to the critical condition of plastic instability for flange, side--wall, corner of punch on blank, The blank holding force in conical part deep drawing is divided into four different regions within its forming figure. The basic principle of reasonable blank holding force during stamping is summarized and provided. The mathematical model of reasonable blank holding force that avoids the wrinkle and rupture is established and verified by the finite element numerical simulation and the grid experiment method. The result shows that it is accurate and reliable.

此外，本文还研究了圆锥形件拉深成形过程中，随着拉深变形过程的进行，毛坯为避免产生起皱、破坏缺陷而对压边力的需求情况，阐明了圆锥形件拉深成形过程中压边力合理变化的必要性；由毛坯主要变形区悬空锥壁部分的受力变形情况，从力学分析的角度，首次推导得出了圆锥形零件悬空锥壁起皱失稳的临界条件；并根据主要变形区法兰、悬空锥壁及凸模圆角部分的塑性失稳临界条件，在其成形范围图中，将圆锥形件成形过程中的压边力划分为四个区域；总结并提出了圆锥形件成形过程中压边力合理变化的基本原则；建立了防止起皱、破坏缺陷产生的压边力合理变化的数学模式，并得到了有限元数值模拟及网格实验法的验证，证实了理论分析结果的正确性和可靠性。

It has been put forward that there exists single Ball point and double Ball points on the symmetrical connecting-rod curves of equilateral mechanisms.

从鲍尔点的形成原理出发，分析对称连杆曲线上鲍尔点的产生条件，提出等边机构的对称连杆曲线上有单鲍尔点和双鲍尔点。

The factory affiliated to the Group primarily manufactures multiple-purpose pincers, baking kits, knives, scissors, kitchenware, gardening tools and beauty care kits as well as other hardware tools, the annual production value of which reaches US$ 30 million dollars.

集团所属工厂主要生产多用钳、烤具、刀具、剪刀、厨具、花园工具、美容套等五金产品，年生产总值3000万美元，产品价廉物美、选料上乘、质量保证，深受国内外客户的青睐