质量因数

Switching multigroup capacitor quickly ,frequently, to keep the electric power factor always in good condition which can reducing the circuit consume in maximum and increasing the transformer's effective output capacity ,optimize the power quality.

对多组电容器进行快速而频繁的投切，使受电功率因数始终保持在最佳状态，从而最大的限度地降低线路损消耗和增加配电变压器的有效输出容量，优化用电质量。

Exploration is done to the relationship of cot structure,cot rigidity to evenness of the resultant yarn and yarn strength;relationship of cot rigidity to friction factor and linear width of nipper jaws;relationship of cot diameter and telescoping tolerance to quality of resultant yarn .

阐述了胶辊结构、硬度与成纱条干、强力的关系，胶辊硬度与摩擦因数、钳口线宽度的关系；胶辊直径、套差与成纱质量的关系；分析了低硬度胶辊改善成纱条干的机理，指出胶辊制作中必须注意的问题及纺纱工艺配置。

The hypothesis on the equivalence in non conservative system is set up for irreversible process on the basis of bring\|in of the nonconservative noninertial system;and the hypothesis on the covariance in non conservative system is put forth for the space time with complex action on the basis of bring\|in of the ultra gauge.

在引入非保守非惯性系的基础上对不可逆过程建立非保守系等效性假设，在引入广域度规的基础上对具有复杂行为的时空建立非保守系协变性假设；利用密度分布的不均匀度h和粗粒熵S及推导的多标度因数η计算式，引入非保守惯性质量和非保守引力质量。

So the immerging of the water and the low quality of the compaction are the reasons on the premature failure of the pavement.

水的浸入和碾压质量不高是造成路面早期破坏的因数之一。

The results show that in the applied load range of 10250 N, the mass loss rate of coated AZ91D alloy can be identified to three stages, which are related with whether the coating is worn out. Abrasion is the main mechanism for the coated alloy. The friction coefficient of the coated alloy during sliding wear appears oscillation before it reaches a constant value, which is close to the μ value of the matrix alloy. The mass loss rate of coated alloy increases slightly with increasing applied load when the applied load is more than 150 N because of high plastic deformation accommodation on the matrix alloy surface.

结果表明：根据载荷大小，涂层处理后AZ91D镁合金的磨损行为明显分为3个阶段，这些阶段同陶瓷层是否磨穿密切相关；微弧氧化涂层AZ91D镁合金的磨损机理主要是磨粒磨损；受表面状况的影响，陶瓷涂层的摩擦因数在 0.20~0.45 间波动；在较高载荷下，涂层被磨穿后，涂层的摩擦因数趋于基体合金的摩擦因数，涂层合金的表面变形能力提高，该阶段质量磨损速率随载荷增加，趋势变得缓慢。

The labia have now been sutured together almost completely.The drains and the Foley catheter come out at the top.

此刻阴唇已经几乎完全的缝在一起了，排除多余淤血体液的管子和Foley导管从顶端冒出来。

To get the business done, I suggest we split the difference in price.

为了做成这笔生意，我建议我们在价格上大家各让一半。