负载

Starting from the steady-state performance of three-phase fully-controlled rectified circuit, which is with large inductive load, we take the front two items of the Maclaurin series of the DC voltage average as approximate formula, with considering of the effect of the AC-side inductance first, and further effect of AC resistance on DC voltage and commutation angle.

本文从带有高感性直流负载的三相全控整流电路稳态工作的物理情况出发，首先考虑了交流侧电感的影响，进而考虑交流侧电阻对直流电压、换相角的影响，将直流电压的平均值用麦克劳林级数表示，取前两项作近似，得出了实用的解析计算公式，并给出了计算步骤，实验证明该结果具有较高的精度。

The catalytic activity of different magnesium chloride treating manner,catalyst milling style and milling time were compared.

采用研磨方式制备了氯化镁负载钛催化剂，比较了氯化镁处理方式及球磨方式和球磨时间对催化活性的影响。

Magnesium chloride supported titanium catalyst was prepared by ball milling style.

研究了负载钛催化剂引发丁二烯在 0～ 4 0℃的本体沉淀聚合动力学。

The device includes on-chip Hall voltage generator for magnetic sensing, the error amplifier that amplifies the Hall voltage, a comparator that is to provide switching hysteresis for noise rejection, the bi-direction drivers for sinking and driving large current load, and the frequency generator thatprovides a signal proportional to rotation speed.

该器件包括片上大厅为磁场传感，误差放大器，放大的霍尔电压，比较器是提供切换噪音抑制滞后电压发生器，双向驱动的吸收和大电流负载，频率方向司机发电机提供了一个信号，转速成正比。

This article introduced the antijamming in the NC system design,from the shield (including electric field shield ,magnetic screen and electromagnetic field shield ) designs mentions,added the absorbing circuit to the perceptual load to suppress the transient state noise to give the specify,might avoid the NC system which disturbed creates softly breakdown.

本文介绍了抗干扰在数控系统中的设计，从屏蔽(包括电场屏蔽、磁场屏蔽和电磁场屏蔽)设计谈起，对感性负载加吸收电路来抑制瞬态噪声做了详细说明，可避免干扰造成的数控系统的"软"故障。

Based on the analysis of calculation theories on magnetic field and torque of permanent magnetic gears, the characteristic curve of torque-angle are calculated with the use of Ansoft electromagnetic calculation software.

本文在分析永磁齿轮磁场和转矩计算理论的基础上，利用Ansoft 电磁计算软件计算了平行轴永磁齿轮的矩角特性曲线，并研究了恒定负载下永磁齿轮的转速波动情况。

The method of how to analyze the electromagnetic field of the generator is introduced. And with the help of a kind of FEM software, the parameters of a model machine are calculated and simulated, including the electromagnetic field, no-load voltage, single-side magnetic force, loaded torque and axial force.

其次，对转子带防护罩的高速永磁发电机数学模型进行了推导，介绍了利用有限元法对电机磁场进行分析的方法，并运用有限元软件对一台样机的参数进行了仿真，包括电机磁场分析、空载电压波形、单边磁拉力、负载转矩以及轴向力等方面的内容。

The least load current to realizemagnetic insulation in MILO is obtained from the relation between current and azimuthmagnetic field and the relation between magnetic field and electron movement track.

根据电流与角向磁场的关系和磁场与电子运动轨迹的关系得到在MILO中实现磁绝缘所需要的最小负载二极管电流。

The main dimensions are calculated by magnetic track, then the fields of load and without load are computed by 2-d FEM and references of the motor are obtained, so the structure of the motor can be adjusted.

用磁路设计法确定电机的主要尺寸，然后用二维有限元法计算电机的空载和负载磁场分布，得到电机的参数和性能，根据性能要求对电机结构尺寸调整。

Considering that the load current contains a little portion of the magnetizing current, this paper presents the approach of magnetizing current compensation.

考虑到负载电流中有小部分励磁电流分量，该文提出串联变压器励磁电流补偿(magnetizing current compensation，MCC)的方法。

And Pharaoh spoke to Joseph, saying, Your father and your brothers have come to you.

47：5 法老对约瑟说，你父亲和你弟兄们到你这里来了。

Additionally, the approximate flattening of surface strip using lines linking midpoints on perpendicular lines between geodesic curves and the unconditional extreme value method are discussed.

提出了用测地线方程、曲面上两点间短程线来计算膜结构曲面测地线的方法，同时，采用测地线间垂线的中点连线和用无约束极值法进行空间条状曲面近似展开的分析。