负角

The reason of white band formation in the solidified shell in the mold has been studied by means of water modeling test and the analysis of the solidified microstructure of practical CC slab an.

为了定量把握结晶器中的钢水流动、钢水过热度及结晶器传热阻力对初期凝固坯壳的凝固不均一的影响，利用水冷铜板的浸渍实验，测定了各种铸造条件下的凝固坯壳厚度、凝固不均一度及树枝晶偏角；利用水力模型实验，并对实机铸坯的凝固组织分析，EPMA对负偏析带的线分析，得出了在结晶器中凝固坯壳上负偏析带的产生原因。

Also choose elevation angles as positive above the boresight axis and negative below, and choose azimuth angles as positive in a clockwise direction and negative in a counterclockwise direction.

同时规定波束仰角在视轴线以上为正，以下为负，方位角以顺时针方向为正，逆时针方向为负。

The concept of negative shear zone and negative shear angle are proposed in study.

提出了负剪切角及负变形区的概念。

In this paper, the negative land angle s of PCBN tools was determinedwhen the cutter was used to cut hardened steel.

本文研究了PCBN刀具负倒棱前角的合理选择，并用X射线衍射仪测量了加工表面残余应力，分析了负倒棱前角在形成表面残余压应力过程中的作用。

This is a clockwise direction so you must hold down the Shift key to specify the angle graphically or enter a negative angle with the keyboard.

这是顺时针方向的，所以用户必须按住 Shift 键来指定角的位置或是用键盘键入负角。

Such as the cutting width reduced to 50% below the pressure angle as a negative angle, cutting feed direction of resistance and inconsistent, it will cause vibration.

如切削宽度减小到50%以下，压力角成为负角，切削抗力与进给方向不一致，就会引起振动。

Skiving cutter adopts larger negative rake angle and negative tilt angle.

刮削刀盘需要采用大的负前角和大的负刃倾角。

The negative shear area and angle φ′of negative shear plane in metal cutting are first found out and verified by experiments, and effects of angle φ′of negative shear plane on the change of cutting direction fracture formation is experimental studied in orthogonal cutting.

首次提出并证实了金属切削中负剪切区域和负剪切角φ′的存在，讨论了负剪切角φ′对切削方向亏缺形成及其变化的影响。

The fiber length has only little influence on the basic density within the growth rings, and significant correlation at 0.01 levels was found between the basic density and the fiber length among the different rings. Only slight negative correlation was found between the basic density and the fiber width within the growth rings, but significant positive correlation at 0.01 levels was indicated between the basic density and the fiber width among the growth rings, contrary to that of fiber length. It was demonstrated that significant positive correlations at 0.01 levels between the basic density and fiber double wall thickness, fiber length to width ratio and double wall thickness to diameter ratio, significant negative correlations at 0.01 levels between the basic density and fiber diameter and diameter to width ratio, only slight negative correlation between the basic density and fiber width both in the same growth rings and among the different growth rings. No significant correlation was found between the basic density and the vessel morphological features, nor was the tissue proportion in the same growth rings. But among the different rings, it was found there was significant positive correlation at 0.01 levels between the basic density and the fiber proportion among the different rings, and significant negative correlation at 0.01 levels between the basic density and vessel-elements proportion and ray proportion, only slight negative correlation between the basic density and the parenchym proportion. Significant or no significant negative correlation was found between the basic density and the microfibril angle in the same growth rings, but significant negative correlation was found between the basic density and the microfibril angle among the different growth rings.

生长轮内纤维长度对基本密度的影响不大，而在不同生长轮间纤维长度与基本密度达极显著正相关，纤维宽度与此相反，同一生长轮内纤维宽度与基本密度极显著负相关，不同生长轮间只有微弱负相关；基本密度与纤维双壁厚、长宽比、壁腔比在生长轮内和生长轮间均呈极显著正相关，而与胞腔直径、腔径比均呈极显著负相关，仅与纤维宽度呈微弱的负相关；导管形态对基本密度的影响不显著；同一生长轮内组织比量对基本密度的影响也不显著，但不同生长轮间基本密度与纤维比量呈极显著正相关，与导管比量和木射线比量呈极显著负相关，与轴向薄壁细胞比量仅呈不显著负相关；生长轮内基本密度与微纤丝角呈显著或不显著负相关，但在生长轮间这种负相关达到极显著水平。

In order to solve this problem, a control strategy is developed. A control algorithm to suppress negative sequence current through ASVG caused by slight asymmetry of system is also developed based on the modeling method in function of switchings and the definition of instantaneous negative sequence voltage. The ASVG can generate a negative sequence voltage component against that in the system while it generating positive sequence voltage with this algorithm.

在系统轻度不对称时，本文提出了通过控制ASVG触发脉冲使其产生与系统电压负序分量大小和相角完全相同的负序电压以抵消系统电压负序分量，从而抑制ASVG负序电流的方法，并用&开关函数&建模法给出了具体的控制算法。

Plunder melds and run with this jewel!

掠夺melds和运行与此宝石！

My dream is to be a crazy growing tree and extend at the edge between the city and the forest.

此刻，也许正是在通往天国的路上，我体验着这白色的晕旋。