负荷

This paper presented an analytical basis and criterion for undervoltage load shedding in power systems.

在分析低电压切负荷机理的基础上，提出了一种新的低电压切负荷控制算法。

Therefore, the development trends are: to establish the dynamic NSP pollutant transport and transformation model which can be applied easily to ordinary natural watershed; to study the estimation methods of NSP load and model parameterized in terms of geomorphic parameters (Horton's numbers) for ungauged watershed.

因此，发展趋势为：第一，建立以污染物迁移转化机理为基础的、适合于野外流域和便于推广应用的非点源污染负荷模型；第二，研究无资料地区的非点源污染负荷估算方法与模型参数估计途径。

It was found that in the heat melting process of the ice layer, the ice melting rate history undergoes 3 stages:unmelting stage, accelerating melting stage, and decelerating melting stage, they are affected obviously by the heat load. The energy utilization effect in the ice melting process may be improved using variable heating.

研究表明，冰层热融过程中，融冰率变化经历未融、融化加速和融化减缓3个阶段，每个阶段受热负荷作用影响明显，若采用变负荷加热，可更有利于融冰过程能量利用的综合效果。

The fresh dewater digested sludge of municipal wastewater treatment plant was suited for vaccinal sludge at the startup of anaerobic reactor and the concentration should not be less 10mg/L; the COD of feed wastewater should be lower than 5000mg/L, and VOL was 20 percent of total VOL; the alkalinity of effluent should be more than 3000mg/L; on the condition of the COD removed 80% can the VOL be elevated.

反应器启动时接种污泥可以选用城市污水处理厂新鲜的脱水消化污泥，浓度不低于10mg/L；进水有机物浓度不高于5000mg/L，容积负荷为满负荷的20％；出水碱度要高于3000mg/L，温度稳定；在有机物的降解率达到80％后再提高负荷。

The operation result of UASB combined with A-SOMBR treating leachate:when volumetrical loading rates were in the range of 0.76-1.61kgCOD/(m3·d), the average removal of COD was 82.66% and the average value of COD in effluent was 188.46mg/L;When volumetrical loading rates in range of 0.058-0.23kgNH3-N/(m3·d),the removal of NH3-N was 88.22% and NH3-N concentration declined to 27.02mg/L.

UASB+A-SOMBR组合工艺处理垃圾渗滤液的研究结果表明：在容积负荷0.76-1.61kgCOD/(m3·d)内，A-SOMBR对COD平均去除率为82.66%，出水COD平均值为188.46mg/L；在容积负荷0.058-0.23kgNH3-N/(m3·d)范围内，A-SOMBR对于UASB产水中氨氮平均去除率88.22%、出水氨氮平均值为27.02mg/L。

A simulation of storm runoff treatment with three types of subsurface flow wetlands of the pilot-scale bed of blank plant,Phramites communis and Zizania caduciflora was studied.

进行了3种人工潜流湿地(无植物空白床、芦苇床、茭草床)控制暴雨径流中氮、磷浓度的冲击负荷试验，考察了潜流湿地对氮、磷的去除效果及其耐冲击负荷能力。

This paper presents a new reactive power compens ator to reduce the negative and zero sequence components of load currents and to improve the load bus power factor of unbalanced three-phase three-wire and three-phase four-wire distribution feeders.

提出了一种用于补偿不对称负荷产生的负序、零序分量并调整负荷母线电压，且适用于三相三线制和三相四线制系统的新型无功补偿器。

Rectifier is not installed, the generator produces a current directly to the battery followed by the system to consume and to have a greater load on the battery installed will enable the supply of power after the stability of demand for power will follow the natural stability of the vehicle power load will naturally improve.

未装设整流器时，发电机产生的电流直接到达电瓶后，随即被系统给消耗并且对电瓶产生较大负荷，装设后可使供应电源稳定，自然需求电源也会跟随稳定，车辆的用电负荷自然会获得改善。

The algorithm is to find all the alternatives of power service restoration paths to the isolated subsystem firstly, and then the optimum scheme may be determined according to the magnitude of the first order moment of the load that the isolated system should transfer to different liaison nodes.

该方法首先对故障元件隔离之后的&孤立岛&求出所有可能的恢复供电路径，根据需要转移的负荷到各路径联络节点的一阶负荷矩的大小，确定最佳的供电恢复方案。

This paper introduces methods of choice data which is about the sensible latent load and MoiSpuie load of automobile airconditioning.

而汽车空调的舒适性评价参数主要是指汽车空调的热、湿负荷，即汽车空调热、湿负荷是确定空调系统送风量和空调设备容量的基本依据。

However, as the name（read－only memory）implies, CD disks cannot be written onorchanged in any way.

然而，正如其名字所指出的那样，CD盘不能写，也不能用任何方式改变其内容。

Galvanizes steel pallet is mainly export which suits standard packing of European Union, the North America. galvanizes steel pallet is suitable to heavy rack. Pallet surface can design plate type, corrugated and the gap form, satisfies the different requirements.

镀锌钢托盘多用于出口，替代木托盘，免薰蒸，符合欧盟、北美各国对出口货物包装材料的法令要求；喷涂钢托盘适用于重载上货架之用，托盘表面根据需要制作成平板状、波纹状及间隔形式，满足不同的使用要求。