负荷

As one of the important aspect of RRM in TD-SCDMA system, CAC is based on the measure of burden on a cell, so find a method to reckon the burden on a cell become important.

接纳控制是TD-SCDMA系统无线资源管理中一个重要方面，它建立在对各小区负荷的测量基础之上，因此，小区负荷的计算方法成为一个十分重要的研究问题。

The global convergence and the convergence speed of ANGA are more satisfier than SGA.

并进行了仿真实验，将由ANGA优化的负荷分配结果与经验负荷分配结果进行了比较。

A 5. 5h anti-impinge test indicated that the whole technical process had a better anti-impinge ability The feasibility modeling test of water quality showed that the quality of reclaimed water after the treatment by the above process, when used as supplementary circular cooling water and boiler water, met the nation standards in the respect of corrosion, scaliness and bacteria breeding, and even better than the normally used cooling water.

以炼厂实际外排污水为原水，通过两期水力负荷分别为0.2m3/h和0.5m3/h中试规模测试，当本工艺处理水力负荷0.5m3/h、水力停留时间1.49h，污水中COD、氨氮、石油类、悬浮物、挥发酚的浓度变化分别为44.07～102.13mg/l、28.37～50.01mg/l、4.68～19.36mg/l、7.2～34.5mg/l、0.14～0.31mg/l时，平均去除率分别达到94％、96.1％、91.9％、98.2％、100％，出水各项指标均符合循环水补充水水质要求；且通过5.5h抗冲击实验结果显示，整体工艺具有较强的抗冲击能力。

Spherical Roller Bearing Raceway surface curvature of the center and center bearings, aligning with the performance, in the case axis deflection can be adjusted automatically, without increasing the burden of bearing, affordable way of radial and axial load capacity, Radial load capacity of large, heavy-duty applicable, the impact load of occasions.

圆锥滚子轴承的内、外圈具有锥形滚道，滚道之间装有锥形滚子，圆锥滚子轴承主要用城承受以径向负荷为主的径向，轴向联合负荷。轴承的内组件和外圈可以分离，方便了安装和拆卸。轴承的轴向承载能力由接触角α决定，α角越大，轴向承载力越大。

The synthetical load modeling method based on load analysis and classification is put forward.

提出了基于负荷分析与分类的综合负荷建模方法。

In this experiment the surface structure of seed coats was observed and a test of the quantity of teliospore on the seed coat was done. The result indicated that the deeper and more the longitudinal grooves and villoses the seed coat are the larger the teliospore's quantity is.

试验主要对六个红花品种种皮上锈菌冬孢子的负荷量与其种皮表面结构进行了观察，查明种皮纵沟较多、较深，且表面绒毛较多的品种，冬孢子负荷量较大，反之则少。

Using the opened thermosiphon of 38x3 as experimental element and water as working fluid,the characteristics of dynamic low load boiling,stable severe boiling heat transfer coefficient and critical heat flux are gotten for the opened thermosiphon at the pressure of 0.02-0.1MPa and 0.1-0.8MPa respectively,which makes up the drawback that the opened thermisiphon has not yet accurate boiling heat transfer relationship formulas.

本文以工程上常用的Φ38×3的开口封底为实验元件，以水为工质，对开启式热管内的动态低负荷沸腾、稳态旺盛沸腾及临界沸腾特性进行系统的可视化实验研究，实验压力为0.02～0.8MPa，实验得出了Φ38×3的开口封底管在工作压力为0.02～0.8MPa和0.1～0.8MPa下的管内沸腾传热系数及临界热负荷计算关联式，弥补了开口封底管——这一新型传热元件尚无准确的沸腾换热关联式的缺陷。

The cooling load of air-conditioning system is a nonlinear model with dynamic and indeterminacy.The traditional way is difficult to predict cooling load to a nicety and celerity.

空调系统负荷是一个典型的具有动态性、不确定性等随机特性的非线性模型，传统方式难以实现准确、快速地预测空调系统动态负荷。

Based on physical characteristics, existing stochastic estimation methods of equipment sensitivity to voltage sag use subjective probability models to express the probability distribution of voltage tolerance curve of equipment in the uncertain region. But the parameter estimation needs vast sample data. These methods may result in man-made errors.

现有负荷敏感度随机估计法以电压暂降的物理特征为基础，用主观概率模型描述负荷电压耐受曲线(voltage tolerance curve，VTC)的随机分布规律，所需样本量大，在实际中难以实现且可能引入主观误差。

Torsional Strength—Measure of the ability of a material to withstand a twisting load.

扭转强度—衡量材料抗扭曲负荷的能力，是材料受扭曲负荷后的极限强度，也是材

However, as the name（read－only memory）implies, CD disks cannot be written onorchanged in any way.

然而，正如其名字所指出的那样，CD盘不能写，也不能用任何方式改变其内容。

Galvanizes steel pallet is mainly export which suits standard packing of European Union, the North America. galvanizes steel pallet is suitable to heavy rack. Pallet surface can design plate type, corrugated and the gap form, satisfies the different requirements.

镀锌钢托盘多用于出口，替代木托盘，免薰蒸，符合欧盟、北美各国对出口货物包装材料的法令要求；喷涂钢托盘适用于重载上货架之用，托盘表面根据需要制作成平板状、波纹状及间隔形式，满足不同的使用要求。