调试

First of all, this thesis introduces the configurations of mechanism system and control system, describes the PID characteristics parameters and their means, analyses the controlled system's stability and debugs the system based on the theory characteristic, and get some good debug methods.

首先，本文介绍了受控五杆机构的机械系统和控制系统结构，阐述了试验台的PID控制参数特性及其意义，并在其PID理论基础上对基于PMAC控制器的五杆机构进行了稳定性分析及调试，总结出了其相应的调试方法。

Basing on the characteristics of fruit and vegetable dewatered wastewater, the process of UASB, biocontact oxidation and flocculation is adopted. By introducing the sludge cultivation and adjustment in the commissioning, and analyzing the problems during operation, factors which may affect process commissioning are raised, as well as the related control measure.

针对水果、蔬菜脱水废水的水质特点，采用UASB/接触氧化/混凝沉淀工艺，通过介绍调试中污泥的培养与驯化，分析运行中遇到的问题，提出了影响工艺调试的因素及相应的控制措施。

The circuit board of the robot control system based on LF2407A DSP chip is designed, and the hardware and software are tested. The control subroutines are programed and tested.

设计了基于LF2407A DSP芯片的机器人控制系统试验平台，进行了硬件电路的设计和调试，并编写调试了控制模块的子程序。

The technology insures the commissioning without oil consumption from the pipe blowing to the end of 168 hours full load, operation with good economic benefit.

介绍了等离子点火技术的工作原理和系统组成，以某电厂3号600MW机组的调试过程为例，阐述等离子点火技术在机组调试中各个阶段的应用，实现了锅炉从吹管到168h满负荷试运行结束&零油耗&的目标，创造了良好的经济效益。

A The adjustment of VIDEO channel is different with other channel, because the color analyzer probe position is different as showed in the following figure:In this area, the luminance should be 90 cd/m2In this area, the luminance should be 5 cd/m2

a VIDEO 通道的调试和 HDTV 以及 PC 通道的调试略有不同，主要是因为在 HDTV 和 PC 中的色分析仪检测点位于屏幕的上半部分，而 VIDEO 通道的色分析仪检测点位于屏幕的下半部分，如下图所示

Double deck Co-extrusion plastics decorative board with soft surface layer;2. Adjustment of the co-extrusion tooling is very important for producing high-quality colored co-extrusion plastic profiles.

塑料异型材表面彩色复合共挤在国内日益兴起，对该类挤出模具的调试是获得满意共挤出异型材的关键之一，现结合共挤模具，探讨了共挤工艺参数的设定、共挤层厚度的控制、共挤层表面质量的控制、共挤层与基材的粘结强度等共挤出模具的调试技

One, and I would frankly prefer people not to use kernel debuggers that much.

使用内核调试器。因此我不会将其作为评定的标准，如果现有的调试器没有被人们很好的了解，我

This meant they were illegal; the debuggers' developers were sent to prison.

这意味着，调试器是非法的；调试器的作者被关进了监狱。

Typically, debuggers are configured to stop on second chance exceptions and allow you to debug.

通常情况下，调试器被配置为阻止第二次机会异常，并允许您调试。

According to the calibration information, Research and development status of automotive bus network and automotive calibration system is studied and the research significance is generalized. First of all, the collectivity precept for calibration system is designed, the calibration platform is set up based on the XCP Protocol and the calibration object is CAN bus network simulation ECUs. Then how to create the calibration system based on Ethernet and Series communication is expatiated, the communication way from computer to ECUs is introduced and the calibration system is tested. Then how to create the calibration system based on CAN bus communication is expatiated, the design and the interface programme are introduced and the calibration system is tested. At last the platform is used to calibrate the CAN bus network simulation system to regulate the simulation system's topology and communication speed to test the communication protocol's feasibility.

论文首先设计了标定系统的总体方案，以CAN总线实时仿真系统中的节点标定为研究对象，采用XCP协议建立具有串口、以太网和CAN总线三种通讯接口的标定平台；然后，具体开发了基于以太网通讯和基于串口通讯的标定系统，完成了上、下位机部分的软件设计，确定了标定系统在两种通讯方式下的数据处理方法，并分别应用两种标定方式标定下位机仿真系统的参数，让下位机仿真系统在规定的通讯协议和拓扑结构下进行仿真，对所设计的标定系统进行了调试；接着，设计了基于CAN总线通讯的标定系统，完成了CCP协议（&XCP on CAN&）的接口程序设计，并通过混合动力汽车一种拓扑结构的通讯仿真对所设计的系统进行了调试；最后，应用开发的标定系统，对混合动力电动汽车网络通讯协议进行了仿真研究，并根据实验结果进行了分析。

However, as the name（read－only memory）implies, CD disks cannot be written onorchanged in any way.

然而，正如其名字所指出的那样，CD盘不能写，也不能用任何方式改变其内容。

Galvanizes steel pallet is mainly export which suits standard packing of European Union, the North America. galvanizes steel pallet is suitable to heavy rack. Pallet surface can design plate type, corrugated and the gap form, satisfies the different requirements.

镀锌钢托盘多用于出口，替代木托盘，免薰蒸，符合欧盟、北美各国对出口货物包装材料的法令要求；喷涂钢托盘适用于重载上货架之用，托盘表面根据需要制作成平板状、波纹状及间隔形式，满足不同的使用要求。