调试

Fact, a just-in-time debugger, and it is difficult for a debugger to get

事实上，在，实时调试器，是很难获得一个调试器

Safety injection actuation test was performed at Full-scale Simulator of QinshanⅡNPP, the initial condition for the test was same as one for the SI actuation test of Unit 1 during commissioning. SI signal was triggered by low-low steam pressure through opening the steam dump valves to atmosphere. Comparing the results obtained from the simulator and real data from the commissioning of Unit 1 showed that the results from the simulator were more conservative from view points of safety, so the models and parameters for the simulator were credible.

在秦山第二核电厂全范围模拟机上进行1号机组调试期间安注试验工况下的安注试验(打开主蒸汽大气排放阀产生主蒸汽压力低低信号触发安注信号)，得到的结果与调试得到的实际数据进行比较，发现从安全方面考虑，模拟机得到的结果更为保守，说明模拟机计算模型和参数设定是可信的。

Split paned message window see the results of your code changes immediately with the split paned message window .

在调试代码时，调试窗口中红色代表有所变化的变量。

Debugging software is needed in the recognizing phase, it is used to watch the execution state, when all planted plane cubic tree structures are detected, they will be decoded into n natural numbers, and the original product of two prime numbers will be got through Chinese Remaining Theory.

水印的检测可以通过调试软件来实现，让调试软件监督嵌入水印的受维护程序的执行，当检测到全体n个PPCT构造后，将它们全体解码为n个天然数，最后应用中国剩余定理将这n个天然数还原出最初的两个大质数的乘积亦即最初的水印信息。

The paper introduces PLL with elaborating its principal, the filter of the loop and the theories of noise. In the following chapter, some binds of dielectric resonator oscillators, especially, their operational principle, are introduced. And then the paper expatiates the design, emulation and the implementation of hardware of the DRVCO in this task, and the design and debugging of the PLL.

本文先介绍了锁相环，对它的的工作原理，环路滤波器的设计及噪声理论进行了阐述，然后介绍了振荡器的工作原理，分类和噪声；并在此基础上介绍了一些常见结构的介质谐振器稳频振荡器的工作原理，接着详细论述了本课题中DRVCO的设计、仿真和硬件实现，以及锁相环路的设计和调试，以及在调试中对低相噪的实现所进行的研究，并给出了结论。

Focus on the installation and modulation, this article mainly introduces the factors and debugging methods in the process of site selection and installation of satellitic ground receiving antenna, as well as some experiences accumulated from the practice of village-to-village connection projects.

重点介绍卫星地面接收天线的安装与调试过程中，卫星地面接收天线的选址所要考虑的因素与调试方法，同时介绍在村村通工程中总结的一些经验。

To use the Petri Nets graphical modeling sententiously and intuitively, the thesis is about the way to using Visual C++ development environment to develop a constitute and debug tool found on the Petri Nets GUI. The essential request is the stabilization of running, the simplicity of operation, the friendliness of the User Interface, and the utility and sufficiency of the functions. Users can draw and edit the Petri Nets model diagram through the standard GUI, and also can observe and debug the migration. It is also helpful to promote the applications.

为了更好的利用Petri网简洁、直观的图形建模方法，本论文旨在通过Visual C++开发环境开发一款基于图形界面的Petri网模型建立和调试工具，其基本要求是：运行稳定，操作简单，界面清晰友好，功能实用够用，用户可以通过标准图形界面的方式绘制，编辑Petri网模型图，并对其迁移过程进行观察和调试，便于推广应用。

To use the Petri Nets graphical modeling sententiously and intuitively, the thesis is about the way to using Visual C++ development environment to develop a constitute and debug tool found on the Petri Nets GUI.

为了更好的利用Petri网简洁、直观的图形建模方法，本论文旨在通过Visual C++开发环境开发一款基于图形界面的Petri网模型建立和调试工具，其基本要求是：运行稳定，操作简单，界面清晰友好，功能实用够用，用户可以通过标准图形界面的方式绘制，编辑Petri网模型图，并对其迁移过程进行观察和调试，便于推广应用。

I have the square wave signal debugging procedures, in order to use the project to open.

本人调试TMS320C54X产生方波信号的调试程序，打开工程即可使用。

The goal of Tuba is to provide a debugging environment similar to traditional source level debuggers for other languages.

它的目标是提供一个调试环境，类似于传统的为其他语言的源水平调试器。

However, as the name（read－only memory）implies, CD disks cannot be written onorchanged in any way.

然而，正如其名字所指出的那样，CD盘不能写，也不能用任何方式改变其内容。

Galvanizes steel pallet is mainly export which suits standard packing of European Union, the North America. galvanizes steel pallet is suitable to heavy rack. Pallet surface can design plate type, corrugated and the gap form, satisfies the different requirements.

镀锌钢托盘多用于出口，替代木托盘，免薰蒸，符合欧盟、北美各国对出口货物包装材料的法令要求；喷涂钢托盘适用于重载上货架之用，托盘表面根据需要制作成平板状、波纹状及间隔形式，满足不同的使用要求。