调整螺钉

Before assembling the ball valve seat sealing surface and be equipped with decent research, and then placed in the closed position the sphere, the installation of left valve, adjusting the gasket, tighten the screws, static pressure irrigation does not leak, this valve can be guaranteed under the seal test seal.

装配前阀座密封面与球体面应配研，然后将球体置于关闭位置，安装左阀体，调整垫片，拧紧螺钉，静压灌水不漏，则此阀在密封试验下即可保证密封。

Side view of fillister head slotted screw with adjustable thread length.

螺纹长度可调整的槽头螺钉的侧面图。

Side view of wing screw with adjustable thread length.

螺纹长度可调整的翼形螺钉的侧面图。

This special piano chair swivels round on a large screw so that you can put it at the right height.

这张特制的钢琴用椅有一大螺钉支撑，以便使演奏人调整到合适自己的高度。

The head of the femur.This special piano chair swivels round on a large screw so that you can put it at the right height.

这张特制的钢琴用椅有一大螺钉支撑，以便使演奏人调整到合适自己的高度。

Press the axle end to the bottom, draw the brake wheel 2, and make it close to the tape of behind cover, revolve the nut 5 clockwise, make it touch with the brake wheel, continually revolve the nut for one to one and a half ring, lock the screw and wind window.

4顺轴下压转轴端部至底，提取制动轮2使其制动环与后端罩3锥面贴合，顺时针方向旋转锁紧螺母5，使其与制动轮端面接触，再将锁紧螺母继续按顺时方向转一圈至一圈半，上好锁紧螺钉和通风窗，调整完毕。

Pressure-relief valve is installing to use , should open the shut-off valve of the road of bypass pipe , remove the mixture of soda and the condenser water in pipeline, in order to avoid that pressure-relief valve produce water when opening 圾 phenomenon damage pressure-relief valve, will be the same as frequently phenomenon rear, press to obey the direction of hour hand slow revolving regulation screw, adjust outlet pressure to needed pressure ( is subject to valve rear gauge pressure ), adjustment is rear, carry locknut , twist protection cover.

减压阀在安装使用时，应把旁通管道的截止阀打开，排除管路中的冷凝水和汽水的混合物，以防减压阀开启时产生水圾现象损坏减压阀，当无异常现象后，按顺时针方向缓慢旋转调节螺钉，将出口压力调至所需的压力，调整后，将锁紧螺母背紧，拧上防护罩。

Relations in accordance with the machines to install the rack assembly components, rack location placed slightly tight after all the connecting screws, adjust the rack so that the eight rack Thread smoothly cylindrical pin penetration, fastening screw connection .

按照机器的装配关系先安装机架组件，机架位置放好后稍带紧所有的联接螺丝，调整机架使机架上的八个内螺纹圆柱销钉都能顺利穿入，紧固连接螺钉。

Loosen screw of stroke stop, and use screw-driver to knock lightly stroke stop, which

松开行程挡块的螺钉，用螺丝刀轻敲行程挡块，即可调整行程挡块的角度，从而改变

After the gauge has been inserted and adjusted, the thumb screw is tightened and the tool removed for measurement of mismatch.

插入该测量仪并进行调整，拧紧翼形螺钉，然后取出该工具以测量偏移率。

They weren't aggressive, but I yelled and threw a rock in their direction to get them off the trail and away from me, just in case.

他们没有侵略性，但我大喊，并在他们的方向扔石头让他们过的线索，远离我，以防万一。

In slot 2 in your bag put wrapping paper, quantity does not matter in this case.

在你的书包里槽2把包装纸、数量无关紧要。