调整螺母

After finished the drawbar spring disc alignment then fix the spring disc stopper, and turn in let the spring disc total length to the standard length (114pcs about 277mm), then the drawbar top fix the M16x1.5 nut.

连接杆弹簧圆盘调整成一直线，然后固定弹簧圆盘的止动块，使之总长为标准长度（114个约277mm），再在连接杆顶部固定M16x1.5的螺母。

Gyrator pressure through the two semi-circular ring mounted on the transfer case on the ring nut can loosen pressure drilling within 360 ° angle in any adjustment.

回转器通过两只半圆压圈装于分动箱上，松动压圈螺母可对钻孔倾角在360°范围内任意调整。

Other standard appointments include figured acrylic trapezoid fingerboard inlays, a corian nut, Gibson's legendary Tune-o-matic bridge and stopbar tailpiece and new quick-connect control pocket assembly.

其他标准任命包括占有丙烯酸梯形键盘芯片，一个可丽耐螺母，吉布森的传奇调整邻马蒂奇桥梁和stopbar附属物和新的快速连接控制口袋大会。

The length of the standard union nut is modified to be slightly shorter for the 1-1/4"- 2" sizes of TU 3-Way Multiport and Diverter Valves.

用于DN32 - DN50的TU三通多通阀个分流阀阀门的标准管接螺母的长度经过调整后会稍微短一些。

Press the axle end to the bottom, draw the brake wheel 2, and make it close to the tape of behind cover, revolve the nut 5 clockwise, make it touch with the brake wheel, continually revolve the nut for one to one and a half ring, lock the screw and wind window.

4顺轴下压转轴端部至底，提取制动轮2使其制动环与后端罩3锥面贴合，顺时针方向旋转锁紧螺母5，使其与制动轮端面接触，再将锁紧螺母继续按顺时方向转一圈至一圈半，上好锁紧螺钉和通风窗，调整完毕。

First, the use of notes 1-1 products for the short form of wedge-type engine connecting circular cone chuck ; 1-2 cards similar form of Shuchi Type ; 1-3 chuck installation : 1-3-1 will be the most fuel piston onto the end 1-3-2 unloaded chuck Fangchenge will chuck fixed transition to the main site, and then push and pull with the adjustment nut to wedge tube wrenches hearts sets top face below the front face plate intimate 1mm; 1-3-3 loaded Fangchenge; 1-4 regular monthly use of the process should be clear brush to avoid internal malfunction.

请各位大虾帮小弟翻译一下使用说明书不胜感激！一、使用说明 1-1 本产品为短圆锥连接形式的楔式动力卡盘；1-2卡爪形式为梳齿式；1-3 卡盘的安装： 1-3-1 将油缸活塞推到最前端 1-3-2 卸下卡盘防尘盖，将卡盘固定到主轴过渡盘上，然后用筒子扳手调整推拉螺母使楔心套顶面低于盘体内腔前端面1mm； 1-3-3 装上防尘盖； 1-4 使用过程中应每月定期清刷，以免内部发生故障。

Our main products: Lower gusset plate, Crank shafts, Wheel hub, Hook, Shifting fork, Lever end, Container forging, Screw nut, Connecting rod, Adjusting arm, Petroleum machinery, Universal coupling, Rock arm and Deformed forging, etc.

主要产品：下联板、曲轴、轮毂、吊钩、拨叉、杆端、集装箱锻件、螺母、连杆、调整臂、石油机械、万向节叉、摇臂、异形件等多个品种及型号。

Pressure-relief valve is installing to use , should open the shut-off valve of the road of bypass pipe , remove the mixture of soda and the condenser water in pipeline, in order to avoid that pressure-relief valve produce water when opening 圾 phenomenon damage pressure-relief valve, will be the same as frequently phenomenon rear, press to obey the direction of hour hand slow revolving regulation screw, adjust outlet pressure to needed pressure ( is subject to valve rear gauge pressure ), adjustment is rear, carry locknut , twist protection cover.

减压阀在安装使用时，应把旁通管道的截止阀打开，排除管路中的冷凝水和汽水的混合物，以防减压阀开启时产生水圾现象损坏减压阀，当无异常现象后，按顺时针方向缓慢旋转调节螺钉，将出口压力调至所需的压力，调整后，将锁紧螺母背紧，拧上防护罩。

After the adjustment ended, tighten the lock nut.

调整后，就将锁紧螺母拧紧。

Adjustment of this union nut can compensate for wear of TFE seats, with no production loss to remove valve for internal adjustment.

这种管接螺母的调整能够弥补TFE阀座的磨损，避免由于拆卸阀门进行内部调整作带来的损失。

But we don't care about Battlegrounds.

但我们并不在乎沙场中的显露。

Ah! don't mention it, the butcher's shop is a horror.

啊！不用提了。提到肉，真是糟透了。