调整的

The development of highway transportation should fit in with the new situation of rapid and healthy economic development. Moreover, the microeconomic policy is a favorable circumstance.According to the actu

本文结合我省道路旅客运输实际情况，通过对国家宏观调控政策的充分研究和我省道路旅客运输需求的科学预测，全面分析了我省道路旅客运输行业的发展现状和存在的结构性矛盾，对道路旅客运输企业结构调整、运力结构调整、运输经营结构调整、运输组织结构调整、运输站场基

First, the image position information was adˉ justed to get an adjusted matrix. Then, the image was denoised bas ed on the adjusted matrix.

先对图像的空间域信息进行调整，得到调整矩阵，基于调整矩阵对图像进行去噪。

The utility model comprises two steel wire fixing adjustors and a spring ergometer, wherein, each steel wire fixating adjustor comprises front and back adjusting slide blocks, an adjusting support block, a bidirectional vertical adjusting slide block and adjusting bolt and a clip ring; the spring ergometer is connected in series between the steel wire adjustors.

该实用新型包括两个钢丝固定调节器和弹簧测功仪，在那里，每个钢丝固定调节器组成，前台和后台调整滑块，调整支持座，垂直双向调节滑块，调整螺栓，并剪辑环；春天测功仪是连接在一系列之间的钢丝调节器。

Research conclusions: The main influencing factors on design of rail fastenings for ballastless track are rigidity, insulation property, rail height and gauge adjustment ability.

研究结论：影响无碴轨道扣件设计的主要因素是合理刚度、绝缘性能和钢轨高低、轨距调整能力，可按节点静刚度25～50 kN/mm，钢轨高低调整量不小于30 mm，轨距调整量-10～＋10 mm，道床电阻不小于3Ω·km进行扣件设计。

The front part is used for adjusting the left and right sides of the drawer door panels, the back part is used for adjusting the up and down of the door panels and the hole in the middle is used for removing the jointers.

首先把前接码插入抽帮里面，侧面有三个调整件，前面一个用于调整抽屉门板左右摆动；后面一个用于调整门板上下摆动，中间的孔位用于拆卸前接码。

Firstly, let us install the jointers in the drawer frame. There are three adjusting parts on the sides. The front part is used for adjusting the left and right sides of the drawer door panels, the back part is used for adjusting the up and down of the door panels and the hole in the middle is used for removing the jointers.

首先把前接码插入抽帮里面，侧面有三个调整件，前面一个用于调整抽屉门板左右摆动；后面一个用于调整门板上下摆动，中间的孔位用于拆卸前接码。

Firstly, let us install the jointers in the drawer frame. There are three adjusting parts on the sides. The front part is used for adjusting the left and right sides of the drawer door panels, the back part is used for adjusting the up and down of the door panels and the hole in the middle is used forremoving the jointers.

首先把前接码插入抽帮里面，侧面有三个调整件，前面一个用于调整抽屉门板左右摆动；后面一个用于调整门板上下摆动，中间的孔位用于拆卸前接码。

Instrument calibration will be put in the stage, adjusting the circular bubble center and leveling instrument, the instrument within the scope of compensation, tilt apparatus (even if the equipment from high to low before or after the high-low) at this time if the device reticle cross Sgro at or below the standard target cross-wire, you can compensate by adjusting the device is hanging below the two long screws to correct until the adjustment to the permitted range.

将仪器放于校正台上，调整圆水泡居中并将仪器整平，在仪器补偿范围内，倾斜仪器（即使仪器前高后低或后高前低），此时若仪器分划板十字丝高于或低于标准目标十字丝，则可通过调整补偿器正下方两悬垂的长螺钉来校正，直至调整到允许范围之内。

The proper clearance setting should be at 0.04-0.1mm. The adjustment is achieved by loosening the locknut (fig.2) and turning the adjusting screw. Tighten the locknut after the adjustment is achieved. Alter the initial 1 hour adjustment, this procedure should be performed a few every 2 hours of use.

正确的汽门间隙为0.04-0.1mm之间，间隙调整螺丝被一个固定螺帽固定住，先将固定螺帽放松就可以转动间隙调整螺丝(如图2)调整后每一小时检查固定螺帽有没有松掉，每2个飞行小时检查汽门间隙。

The proper clearance setting should be at 0.04-0.1mm. The adjustmentscrew. Tighten the locknut after the adjustment is achieved. Alter theinitial 1 hour adjustment, this procedure should be performed a fewevery 2 hours of use.

正确的汽门间隙为0.04-0.1mm之间，间隙调整螺丝被一个固定螺帽固定住，先将固定螺帽放松就可以转动间隙调整螺丝(如图2)调整后每一小时检查固定螺帽有没有松掉，每2个飞行小时检查汽门间隙。

This one mode pays close attention to network credence foundation of the businessman very much.

这一模式非常关注商人的网络信用基础。

Cell morphology of bacterial ghost of Pasteurella multocida was observed by scanning electron microscopy and inactivation ratio was estimated by CFU analysi.

扫描电镜观察多杀性巴氏杆菌细菌幽灵和菌落形成单位评价遗传灭活率。