误差补偿

The experimental results show that temperature error and non-linearity of silicon piezoresistive pressure sensor can be reduced markedly.

本文针对其缺点，提出了以正交的局部函数——小波函数作为激励函数的小波神经网络对硅压阻式压力传感器的温度误差进行补偿。

Based on the monitormeasuring loop of error autocompensation INS,a robust adaptive filter is developed in this paper.

针对误差自补偿惯性导航系统的特点，设计了该系统监测回路的鲁棒自适应滤波。

In Chapter 2, the fundamental theorem and functional blocks of the GM-C filter are introduced. After that, the possibility to compensate the fixed and variable errors is discussed.

第二章中，先针对GM-C滤波器的基本原理及功能方块先作介绍，而后，讨论固定及变动误差之可补偿性。

In order to improve scan precision of the laser galvanometer scan system, especially when scan area is large, the reasons of graphic distortion are analyzed in this paper when the laser galvanometer scan system is running, and the whole bag of compensating tricks are put forward for every reason of corresponding graphic distortion.

针对如何提高振镜式激光扫描的扫描精度，特别是当扫描区域较大时的精度问题，文中展开了对振镜式激光扫描时图形畸变原因的分析，并对每一种误差产生的原因提出了校正补偿的办法。

First order coefficient of the phase error function can be estimated by sensor-based motion compensation. Second or higher order term of phase error function could be estimated and cancelled by autofocus technique.

传统由感测器执行之运动补偿功能只能测量到相位的一次项系数，如果加上自动聚焦法，则可以将二阶以上的误差项消除。

The results of simulated analysis have proved the validity of this method. This model can be used as a compensating approach to random errors of IMU.

该模型可用于补偿惯导系统中陀螺漂移产生的随机误差，以提高制导精度。

Error analysis and compensation in laser interferometry.

激光干涉测量中的误差分析与补偿。

The effects of linear acceleration on gyro 's drift have been analyzed.

分析了各种加速度对陀螺漂移的影响，列表给出了载体在各种线振动情况下陀螺的漂移，为工程应用上建立补偿陀螺漂移误差模型提供了理论依据。

In order to solve the problem mentioned above, a new dynamic compensation method using linear extrapolation scheme was presented to compensate the measured output of inductorsyn. Thus the measuring error induced by measuring delay was reduced, and the system tracking precision was enhanced.

为解决上述问题，提出一种动态补偿方法，采用线性外推方法，对圆感应同步器数显表的测量输出进行动态修正，以减小由于测量延迟产生的测量误差，从而提高系统的动态跟踪精度。

An algorithm is established for compensating springback in sheet metal forming based on the theories of linearity closed loop control system, space Fourier transform, and transfer function in frequency domain as well as die experiment iteration.

以冲压件回弹引起的尺寸误差为控制目标，以线性闭环控制系统、空间Fourier变换和频域传递函数为理论基础，基于模具实验迭代，建立了模具回弹补偿修正算法。

But we don't care about Battlegrounds.

但我们并不在乎沙场中的显露。

Ah! don't mention it, the butcher's shop is a horror.

啊！不用提了。提到肉，真是糟透了。