误差范围

The error sources, factors of effect on accuracy and the controllable error range of airborne laser designator are discussed, through the components of airborne laser designator in this paper.

文中通过机载激光指示器的组成分析了它的误差源、影响系统精度的因素以及其可控制的误差范围。

The experimental results show that a good linear relation between TCD response to the partial pressure of deuterium is obtained.

实验结果表明，TCD对氘的响应与氘的压力呈良好的线性关系；对已知氘丰度为1%~90%的氕氘混合物样品进行了测定，测量结果的误差与气氛混合气体中的HD丰度成正比，绝对误差范围在

The maximum error of this method was 15%. A preliminary investigation for effect of direction of the dosimeter pair showed that it was not ...

方法的最大误差为15％，初步进行了该剂量计对的方向性试验，在一定误差范围内可以认为方向性的影响不是严重的。

Also the problems of stochastic controllability, observability and stability of the filter are studied, a simple observability criterion for the time-invariant systems is set up, error band of the filtering is given theoretically, and the filtering stability results are proved under more general conditions; besides, the filtering error caused by uncorrect mathematical models is analysed.

本文还研究了随机能控能观性及滤波的稳定性问题，建立了结构简单的平稳定常系统的能观性判据，在理论上给出了滤波算法的误差范围，在更一般的条件下证明了最优滤波算法的稳定性；并从理论上分析了模型误差对滤波产生的影响。

The computer aided Monte Carlo analysis is applied to it to achieve the influence of the circuit output voltage, which caused by random error of the electronic component.

建立一种功率因数校正电路的计算机模型，并对该模型进行了计算机辅助的蒙特卡罗分析，得到了电路中元器件参数的随机误差对电路输出电压的影响，为电路生产过程中确定元器件的误差范围提供了科学依据。

The error of quadratic interpolation method on sine wave signal was analytically studied and numerical evaluated in this paper.

该文从理论分析和数值仿真两个方面，对二次插值算法在正弦信号分析中存在的误差进行了详细的研究，得到了误差范围的解析表达式。

A simple of improving the differential frequency by D flip-flop is introduced. The method is verified by timing analysis. Numberical application conditions are given out. The reason for the error production is analyzed and the maximum error range are calculated.

介绍了D触发器差频的方法和应用条件，用最基础的时序分析的方法，对D触发器差频做一个理论上的验证，定量给出应用条件，并分析了产生误差的原因和最大的误差范围。

The percentage error during measurement was estimated between 5% and 20%.

分析误差来源合理地估算出实验误差范围为5%至20%。

Although binding quality standards error range specifically, but we can still improve the accuracy of the efforts to reduce the error-fold.

虽然我国装订质量标准对此误差范围有明确的规定，但我们仍然可以通过努力，提高折页精度，减少误差。

Because of the star position error, more triangles within some scope should be selected.

由于获得星点位置的时候存在误差，所以将一定误差范围内的三角形均作为待选三角形考虑。

However, as the name（read－only memory）implies, CD disks cannot be written onorchanged in any way.

然而，正如其名字所指出的那样，CD盘不能写，也不能用任何方式改变其内容。

Galvanizes steel pallet is mainly export which suits standard packing of European Union, the North America. galvanizes steel pallet is suitable to heavy rack. Pallet surface can design plate type, corrugated and the gap form, satisfies the different requirements.

镀锌钢托盘多用于出口，替代木托盘，免薰蒸，符合欧盟、北美各国对出口货物包装材料的法令要求；喷涂钢托盘适用于重载上货架之用，托盘表面根据需要制作成平板状、波纹状及间隔形式，满足不同的使用要求。