误差分析

The conditions of the filters that should be satisfied are also derived. By analyzing the transformation structure of orthogonal wavelets and biorthogonal wavelets, the data acquisition method based on multichannel structure is proposed. The compensation method is discussed, and the design method of compensation filters is also derived.

在分析了正交小波与双正交小波变换的结构的基础上，利用多分辨理论的性质，提出了基于小波方法的双通道及多通道数据采集方法，最后对这种结构中可能存在的误差的补偿方法进行了研究，得出了去除误差的滤波器设计公式，从而完成信号的采集与恢复。

The percentage error during measurement was estimated between 5% and 20%.

分析误差来源合理地估算出实验误差范围为5%至20%。

This paper analyzed the randomness of the relative position relation between the common vertical line of the two axes of a coupling and two centers of a coupling during installing machines,and the randomness of the position of the support plane on which a machine is installed.It pointed out the errors formed by the two randomness and illustrated the faults of the four parameters system which is used in describing the shaft alignment error of a coupling by abroad technician.

分析了机器安装过程中联轴器两轴线的公垂线与联轴器中心的相对位置关系的随机性及机器地脚支承面方位的随机性，指出了两种随机性所产生的误差，说明了国外工程界在描述联轴器对中误差时所用的4参数体系存在的不足。

The additional calculation error of measuring gas flow capacity through planimeter calculating av - erage value between differential pressure and static pressure with dual bellows differential pressure flow capacity table is discugsed in this paper .

本文讨论了从双波纹管差压流量卡片上，用求积仪求得差压和静压的平均值计算天然气流量方法所产生的附加计算误差；分析了差压和静压在不同的变化趋势下，附加计算误差的大小和方向；提出了改进和预防的建议。

This paper brings up with the theory of Virtual Coordinate Measuring System. The basic theoretic models of the virtual coordinate measuring system are given. This theory of virtual coordinate measuring system makes use of the principle of Time-Space correspondence and turns the time pulses into spatial displacement. The virtual coordinate measuring system can take the place of the scale system in traditional instruments, which has the disadvantages of high cost and difficulty ofproduction.

本文同时提出并建立虚拟坐标测量系统理论；该理论从传统的测量仪器出发，将传统仪器的实物标尺系统虚拟化，克服了实物标尺系统加工制造困难，及造价高等缺点，将硬件结构简化；本文提出并建立初步的虚拟坐标测量系统模型，并在三坐标测量机上建立了一维虚拟坐标测量系统的实验模型，初步分析系统的系统误差与其随机误差源。

Quantization error of signals and weight values is considered together, and the simulation result is given at last.

分析既考虑了信号的量化误差，同时又考虑了权值的量化误差，并给出了相应的仿真结果。

Through analyzing the traditional implement method,the phase introduced by the quantization error of the frequency control word is put forward.

介绍了一种对基于DDS的数字本振的改进，分析了传统的数控振荡器的实现方法，指出其中由于频率控制字的量化误差带来的振荡器输出相位误差。

The errors and the influence degree on the precipitable water vapor results are analyzed. Comparison is conducted between retrieved and observed, as well as the radiosonde data. The findings conclude that the retrieved results are applicable.

同时对影响水汽反演的误差进行了分析，给出了各项误差对水汽结果的影响程度，并对反演结果与探空资料结果和实际降水进行了比较，得出了其间变化一致性的结论。

Its results show that in order to maintain desired BER performance the fixed estimalion error should be less than 0.07 dB, thd deviation of random estimation error should be less than 0.6, and the time-delay should be controlled within 0.001/v/λ(subscript c.

分析和仿真结果表明，为了维持系统所需的BER性能，固定估计误差值应小于0.07dB，随机估计误差的离差要低于0.6，而时间延迟应控制在0.001/v/λ

The analysis results show that the system and random error are reduced with this method.

通过定性的分析，该方法能够在一定程度减少系统误差和随机误差。

However, as the name（read－only memory）implies, CD disks cannot be written onorchanged in any way.

然而，正如其名字所指出的那样，CD盘不能写，也不能用任何方式改变其内容。

Galvanizes steel pallet is mainly export which suits standard packing of European Union, the North America. galvanizes steel pallet is suitable to heavy rack. Pallet surface can design plate type, corrugated and the gap form, satisfies the different requirements.

镀锌钢托盘多用于出口，替代木托盘，免薰蒸，符合欧盟、北美各国对出口货物包装材料的法令要求；喷涂钢托盘适用于重载上货架之用，托盘表面根据需要制作成平板状、波纹状及间隔形式，满足不同的使用要求。