误差

This paper analyzes the deviation of cambered form witch is composed of batten and sheet in concrete construction,and then educes a relationship between width of sheet,deviation of cambered form and curvature radius of camber,in order to solve the problem of assemble spline form work and increase construction quality of concrete curved surface.

分析了用板条和铁皮组装而成的曲面模板在曲面混凝土施工中的误差情况，同时给出了施工中板条宽度、曲面误差、曲面曲率半径之间的关系，以解决好拼装样条模板的问题，从而提高混凝土曲面的施工质量。

Then the theory error of three points Gauss fitting method is analyzed and the theory error curve is given.

以三点高斯拟合算法为例，分析了算法的理论误差，并给出了理论误差曲面。

In theory, there is no error for the refractive seismic exploration by permuting the focus and the cymoscope. In some especial condition, it would be the only choice because that refractive seismic exploration is needed, but the error can not be neglected be cause of various factors.

在理论上，用源检互换的方法进行折射地震勘探是没有误差的，在某些特殊条件下无法铺设检波器而又必须进行折射地震勘探时它也是唯一的选择，然而，在实际工作中，由于各种因素的影响，其误差是不可忽略的。

A new calculation model is established using the simulating curves presented by Standing and Katz. The coefficients of the correlation are determined by fitting to the data of Standing and Katz Z-factor chart. The results of the two models are compared, the conclusion can be drawn that the error of LXF model is smaller than that of DAK model.

利用两种模型对不同拟对比温度和拟对比压力组合条件下的天然气偏差系数进行了拟合计算，与理论图版值的误差对比显示，在高温高压条件下LXF模型的拟合结果更优，特别是随着拟对比压力的增加，LXF模型的误差不断减小，因此，该模型更适用于高压和超高压条件下天然气偏差系数的工程计算。

According to the characteristic of the data processing, a interferogram regrouping error correction algorithm is designed, and devise a method to correct the sampling position error of the central dark fringe.

通过对其数据处理流程特点的分析，设计了一种归一化算法，对由干涉图重组时产生的误差进行了校正，并对在数据采集过程中干涉图的中心暗纹位置的采样误差进行了二次曲线拟合校正。

According to the definition of the minimum zone method, the mathematical model is presented for evaluating flatness error and establishing datum plane equation.

分析了常用的近似评定法(三点法、对角线法、最小二乘法等)存在的局限性，根据最小区域法的定义，给出了基准平面方程及平面度误差评定目标函数数学模型的建立方法，并举例说明了采用Matlab进行平面度误差的计算。

Error reduction can be achieved by improving the precision of flow meter, thermometer, water cut meter and densimeter,by reducing sample oil's deviation,and by correcting flow met...

要减少油量计量误差，就必须提高流量计、温度计、含水仪、密度计等仪表的准确度，减少所取油样的密度与含水率在某段计量时间内的非代表性平均值所引起的误差，用流量计系数来修正流量计的示值。

The steepest descent method using the AGC simulation, compared with the average error, and only when the second error control effect.

详细说明：采用最速下降法的AGC仿真，比较了用误差平均和仅用当次误差的控制效果。

However, delivery error of LGWs are mainly the designation error from laser designator.

而激光制导武器投放的主要误差来自于激光目标指示器的指示误差。

The error sources, factors of effect on accuracy and the controllable error range of airborne laser designator are discussed, through the components of airborne laser designator in this paper.

文中通过机载激光指示器的组成分析了它的误差源、影响系统精度的因素以及其可控制的误差范围。

And Pharaoh spoke to Joseph, saying, Your father and your brothers have come to you.

47：5 法老对约瑟说，你父亲和你弟兄们到你这里来了。

Additionally, the approximate flattening of surface strip using lines linking midpoints on perpendicular lines between geodesic curves and the unconditional extreme value method are discussed.

提出了用测地线方程、曲面上两点间短程线来计算膜结构曲面测地线的方法，同时，采用测地线间垂线的中点连线和用无约束极值法进行空间条状曲面近似展开的分析。