误差

The error correction method for microwave measuring line is analyzed, and a new method is proposed which can realize the measurement of error network parameters for microwave measuring line. Then the least square method explicit solutions of error network are given, and the CAT of error network parameters is realized.

分析了微波测量线误差校正的方法，提出了仅用小反射滑动负载即可确定测量线误差网络参数的新方法，给出了测量线误差网络参数的最小二乘法显式解，并实现了测量线误差网络参数的CAT 。

To study the calibration accuracy of stuctured light system based on cross-ratio invariant,measuring error and light-plane calibration error of system are analyzed,and an error propagation model is established by employing theories of error and matrix disturbance.

针对基于交比不变原理的结构光光平面标定方法，利用误差分析理论和矩阵扰动原理分别对系统的测量误差和光平面标定误差进行分析，提出了结构光测量系统的误差传递模型。

Based on analyzing performance of gear machining system and mechanism of machining error, the description method of machining error was presented for gear machine. According to the performance-driven design concept and generalized multi-body certainty theory, driven by gear machining error, machining error fine model and system integrated design method of CNC gear shaper was studied.

本文在分析齿轮加工机床的系统性能和加工误差产生机理的基础上，提出了加工误差描述方法；以&性能驱动设计&为基本理念，以齿轮加工误差为驱动，以广义确定性多体系统为理论基础，研究了数控插齿机加工误差精细分析和系统集成设计方法。

For total absorption coefficient at 443 nm (a443), the root-mean-square-error is 0.046 in the South China Sea, with an averaged percentage error of 7.9%, and averaged error in log scale close to 0. For coastal waters off Fujian, RMSE, an averaged percentage error and δ are 0.194, 30.6%, and -0.167, respectively.

对于443 nm的总吸收系数（a443 ），南海的对数均方根误差为0.046，平均相对误差为7.9%，对数平均偏差为0；福建沿岸水体的对数均方根误差为0.194，平均相对误差为30.6%，对数平均偏差为-0.167 。

Two transverse fast low angle shot sequences (1.5mm slice thickness) were acquired at 3T, and twosagittal MEDICwe sequences (0.6mm slice thickness, isotropic). Thetransverse multiplanar reformats were performed from the sagittalMEDICwe.

在FLASH和MEDIC序列软骨体积测量值与形态学测量值之间的随机配对误差分别是4.3％～6.8％和2.9％～6.6％，系统性误差分别是-0.6％～1.2％和-1.1％～2.8％。2对软骨体积的定量MRI测量，髌骨轴位FLASHwe序列可重复性误差1.2％，MPR MEDICwe序列可重复性误差1.8％。

According to the engage relation of cycloidal gear with the pin wheel in type 2K V transmission,the formulas of relationship between transmission precision and mesh error of the actual profile of gears are established; then a synthesis mesh error is proposed as a quantified concourse of error to judge the transmission error,therefor the machining tolerances relative to transmission precision have quantificational relation,which is the basis for machining high precision 2K V drives with cycloidal gears.

根据 2K—V型传动中摆线轮与针轮的啮合关系，建立了实际齿廓的啮合误差与传动精度关系的计算式，并提出了综合啮合误差这一量化误差集合来评判传动误差，使得加工公差与传动精度有一个定量的关系，从而为研制开发高精度摆线齿 2K V型传动的加工制造提供了依据。

Included are the measurements of the tooth profile deviation of a shaving cutter based on the generalized polar coordinate method, and of the helix deviation of the shaving cutter using curvature method to automatically identify the boundary points; the measurements of the tooth profile of a modified hobbing cutter, and of deviation of contact line of the hobbing cutter by means of the generalized cylindrical coordinate method; the measurement of the deviation of tooth profile of a non-linear worm .

这些测量包括：①基于广义极坐标法的剃齿刀齿廓误差测量，以及采用&曲率法&自动识别界点的剃齿刀螺旋线误差的测量；②修形滚刀的齿廓测量，以及基于广义圆柱坐标法的滚刀啮合误差的测量；③非线性蜗杆的齿廓误差测量。

The tooth contact and kinematic precision of cone-generated double-enveloping worm gearing with machining and assembling errors have been investigated.

对存在加工及装配误差的锥面二次包络环面蜗杆传动进行了接触分析，探讨了各种制造误差对齿面接触质量和运动精度的影响规律和影响程度，提出了矫正由加工误差引起的齿面接触偏倚，减小运动误差的装配调整作业法。

During the course of solving the grinding wheel cross-sectional profile, it also analyses the grinding wheel cross- sectional profile errors and the errors sensitive parameters,which are resulted by the existence of the drill end-sectional errors and the relative position errors between the drill bit and the grinding wheel.

并分析了在求解砂轮截形的过程中，由于存在钻头端截面误差和钻头与砂轮相对位置误差，所带来的砂轮截形误差及其误差敏感性参数。

Position transformation error is a important part in research of north seeking scheme, the thesis analyses position transformation bringing error of north seeking in two-position scheme and brings forward the method of position transformation error measurement and compensation.

在寻北方案的研究中，转位误差是一个不可忽视的部分，文中以二位置为例分析了转位误差引起的寻北误差和转位误差的关系，并提出了测量和补偿方法。

However, as the name（read－only memory）implies, CD disks cannot be written onorchanged in any way.

然而，正如其名字所指出的那样，CD盘不能写，也不能用任何方式改变其内容。

Galvanizes steel pallet is mainly export which suits standard packing of European Union, the North America. galvanizes steel pallet is suitable to heavy rack. Pallet surface can design plate type, corrugated and the gap form, satisfies the different requirements.

镀锌钢托盘多用于出口，替代木托盘，免薰蒸，符合欧盟、北美各国对出口货物包装材料的法令要求；喷涂钢托盘适用于重载上货架之用，托盘表面根据需要制作成平板状、波纹状及间隔形式，满足不同的使用要求。