试验方法

The tensile tests designed by orthogonal test used to test low carbon billet,hot roll armor plate and cold-roll armor plate at room temperature to investigate the influence of tensile rate on mechanical properties have been discussed in this paper.

采用正交试验方法设计拉伸试验方案，对低碳钢坯、低碳热轧及冷轧钢板进行了金属常温拉伸试验，考察试验速率对力学性能的影响。

Reliability test is necessary for high-frequency transformer,especially temperature test. The test method, col?lection of test data and analysis of test results are discussed.

因此，必须对高频变压器进行可靠性试验，特别是温度试验，并对试验方法、试验数据的采集、试验结果的分析进行了介绍。

Focusing on the interaction among the screws,the paper analyzed the current method of determining propulsive factor based on ship s self-propulsion test with three-screw and presented a new method to test and analyzed propulsive factor of ship with multi-screw.

针对多桨船螺旋桨间互相干扰的影响，通过对三桨船自航试验推进因子分析方法进行分析探讨，提出新的三桨及以上的多桨船船模自航试验方法和其推进因子分析方法。

At the same time, on the basis of some various model and standard steam trap experiment, the configuration methods of the date acquisition system and the realization methods of the date processing system are main discussed as well and resolve the problem about the stepwise acquisition and processing of uncontinuous experiment data.

在提出不同型号、不同规格阀门试验方法的基础上，重点讨论了在组态软件MCGS平台数据采集系统的组态方法和数据处理软件的具体实现方法，从而解决了非连续性试验数据的分步采集和复杂处理问题。

This paper introduces the principle of instrumented impact test method and its application in production and scientific research.

介绍了仪器化冲击试验方法的基本原理及其在生产和科研中的应用，重点阐述了仪器化冲击试验方法在动态断裂力学测试技术中的开发、冲击曲线参数分析、材料断裂机理研究等领域所取得的成果，并展望了这一方法未来的应用和发展趋势。

The contact fatigue strength was measured after the 20CrNi2Mo and 15CrNi6 steel used asdragging gear on quasi high speed locomotive was carburized and quenched as well as peened,com-pared with that of 20CrMnMo steel.The results shown that the contact fatigue strength limits of thesethree types of steel carburized and quenched essentially same,and the contact fatigue strength Iimit hasbeen increased by 5 porcent after peening,and that the failure appoarances of all contact fatiguespecimen were delamination ...

对20CRrNi2Mo、15CrNi6及20CrMnMo渗碳淬火齿轮及15CrNi6渗碳淬火＋喷丸处理齿轮进行了弯曲疲劳试验，介绍了齿轮试件的设计与加工、试验装置与夹具、试验方法及试验数据的统计处理，试验结果表明，20CrNi2Mo和15CrNi6渗碳淬火齿轮在R＝0.99时的σFlim分别为530MPa和375MPa，与20CrMnMo渗碳淬火齿轮相比，弯曲疲劳强度分别提高80％和27％。15CrNi6经渗碳淬火＋喷丸处理齿轮在R＝0.99时的σFlim为490MPa，比未喷丸处理者提高30％。

Exhaust purity box is experimented in the way of upright meathed times are less for the multielement and multilevets ,the impact degree on the exhaust purity box canbe got from the experiment data analysis of various elements ,be offered to further the improvement of the exhaust purity box .

利用正交设计试验方法对净化消声器进行试验，在较少的试验次数下进行了多因素多水平的试验，从试验数据的分析中可看出各因素对净化消声器各性能的影响程度，为进一步提高净化消声器的性能提供了参考依据。

First of all, the concept of S-N curve and the procedures of p-S-N curve fatigue test, data processing were introduced. And then, these procedures were taken into practice on 4 kinds of aluminum alloy welded joints: corner joint, butt joint, cruciform joints and double-sided lap joint.

文中首先介绍了S-N曲线的概念和p-S-N曲线疲劳试验方法和数据处理方法，并按照这些方法对角接、对接、十字接和双面搭接四种铝合金焊接接头试样进行了疲劳试验，得出了这四种焊接接头的中值S-N曲线和置信度为95%，存活率分别为90%、99%下的p-S-N曲线及其方程。

Study on the rubber stator compoundof one step injection screw drilling tool;2. he paper presents a test method to research the dynamic property of the rubber stator for screw pump,compares the result of static and dynamic tests and selects the formulation according to the tests.

提出研究螺杆泵定子橡胶动态性能的试验方法，对静态试验及动态试验结果进行对比，并应用其试验对配方进行筛选，结果表明，橡胶压缩温升试验能较好地表征螺杆泵定子橡胶的动态性能，为橡胶定子的研究提供了较为可靠的依据，并在实际应用中得以证实。

The dissertation discusses a compensation method witch need to known exact values of the beading, pitch and roll angle of UAV in experiment.

提出并实施了给定基准法的误差补偿试验方法，并提出了对该方法的试验数据正确性检验方法。

But we don't care about Battlegrounds.

但我们并不在乎沙场中的显露。

Ah! don't mention it, the butcher's shop is a horror.

啊！不用提了。提到肉，真是糟透了。